Permanently Deactivating The Alarm (Off); Switching Off The Alarm; Switching Off The Alarm During Sunrise; Snooze Mode (Snooze) For The Alarm - Beurer WL 70 Mode D'emploi

Monday, as described in the previous point. Then set
the alarm time as described in section 8.1.1.
8.1.3 Permanently deactivating the alarm (OF F)
To permanently deactivate a set alarm, proceed as
follows:
1. When the device is switched on, keep pressing the
ALARM button until the desired alarm memory space
appears in the display (A1, A2 or A 3).
2. Press the / buttons until OFF appears in the display.
3. Confirm using the Menu/Set button.
4. E N D appears in the display. The alarm is now
permanently deactivated.

8.2 Switching off the alarm

8.2.1 Switching off the alarm during sunrise:

When the sunrise function is switched on, the device
slowly begins to light up prior to the set alarm time and
"SUNRISE" is shown in the display. You can switch off
this sunrise by pressing any button. However, the alarm
tone will still sound at the set alarm time.

8.2.2 Snooze mode (Snooze) for the alarm

The device features a snooze mode (Snooze).
If the alarm sounds and you press the Snooze function
(by tapping the light area), the alarm will sound again once
the set snooze duration has elapsed (see section 7.4).

8.2.3 Switching off the alarm when the alarm tone sounds

When the alarm sounds, press any button apart from
Snooze. The alarm is now switched off and will only
sound again at the set alarm time.

8.3 AuX mode

You can connect an external audio source (e.g. MP3
player, smartphone or CD player) to the wake-up light
via the AUX input.
1. Connect the supplied AUX cable to an audio source.
2. Insert the other end of the AUX cable into the AUX input
on the rear of the device.
3. Press the AuX button on the device. The external audio
source is now connected to the wake-up light.
4. Use the +/- buttons on the side to adjust the volume.
5. Press the ■ button to exit AUX mode again.
6. Disconnect the AUX cable after use.

8.4 Radio mode

You can also use the device to listen to the radio.
If you wish to use radio mode, proceed as follows:
1. When the device is switched on, press the FM button.
The current station frequency and programme number
(e.g. P1) appear in the display.
2. Use the / buttons to select the desired programme
number (e.g. P 1 or P 2 ) under which a station is to be
saved.
3. Press and hold the
station search. To save a station under the selected
programme number (e.g. P 1 ) , pre ss th e Menu/Set
button.
4. To switch between the saved stations, press the
buttons.

8.5 Good night function (radio sleep timer)

If radio mode is switched on, you can also enable a good
night function.
You can use the good night function to set the number
of minutes after which the radio should automatically
switch off.
If you wish to use the good night function, proceed as
follows:
1. When the device is switched on, press the FM button
to access radio mode.
2. Press the Menu/Set button; 2 M I N s l e e p appears
in the display.
3. Use the Menu/Set button to set the desired time after
which the radio should automatically switch off (2, 5,
10, 15, 20, 30, 45 or 60 minutes). Wait 5 seconds to
confirm the selection. A small
appear in the display.

8.6 Light functions

8.6.1 Reading lamp

1. When the device is switched on, press the Light button.
2. The light turns on and 20 light appears in the display.
Use the +/- buttons to set the desired brightness for the
light (can be selected between 1-20).
3. To switch the light off again, keep pressing the Light
button until "LI GH T of f" appears in the display.

8.6.2 Sunset function

The device can also be used to simulate a sunset. In the
process, the light slowly turns darker after a set duration.
To simulate a sunset with the device, proceed as follows:
1. When the device is switched on, press the Light button
on the side.
2. The light turns on and 2 0 l i g h t appears in the
display; immediately afterwards, use the +/- buttons
on the side to set the desired brightness of the light
(can be selected between 1-20). Use the Light button
to confirm. 10 sun set appears in the display.
3. Use the +/- buttons on the side to select the desired
duration of the sunset (2, 5, 10, 15, 20, 30, 45 or
60 minutes), then wait for 5 seconds. The sunset
13
button to start the automatic
icon will subsequently
/