Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Operating Instructions & Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or main-
tain the product described. Protect yourself and others by observing all safety information. Failure to comply
could result in personal injury and/or property damage! Save these instructions for future reference.
D
B
ual
Light Control
• D
Z
ual
one
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• D
B
ual
rite
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
This package includes:
Cover Plate
Mounting Bolt
2 Lamps
(installed)
HEA 009
Printed in China
09/07
Get user manuals:
See SafeManuals.com
®
Motion Sensor
®
rite
Features
™ Technology.
®
Timer.
Lamp Holders
Sensor
Light Control
Mounting Strap
6 Screws
(3 sizes included)
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Mode:
Test
Auto
Manual
Accent
Note: When first turned on wait about 1
the circuitry to calibrate.
Rubber Plug
Put ON-TIME switch
on the sensor bottom
to TEST and the D
Plastic Hanger
B
®
rite
Put the ON-TIME switch in the 1, 5,
2 Wire
or 20 minute position.
Connectors
Manual mode only works at night
Gasket
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
2LBL3, 2LBL4
Requirements
OPERATION
On-Time
Works: Day Night
5 Seconds
1, 5, or 20 Min
To Dawn*
3, 6 Hr, to Dawn
* resets to Auto Mode at dawn.
TEST
ON-TIME
-
ual
TEST 1 5 20
switch OFF.
AUTO
MANUAL MODE
x
x
x
x
x
1
/
minutes for
2
D
B
®
ual
rite
Off 3 6 Dusk to
Dawn
ON-TIME
TEST 1 5 20
1 Second OFF
then...
... back on.
598-1325-00
LPG-5597
Publicité
Manuels Connexes pour LumaPro Dual Brite 2LBL3
Sommaire des Matières pour LumaPro Dual Brite 2LBL3
- Page 1 Operating Instructions & Parts Manual 2LBL3, 2LBL4 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or main- tain the product described. Protect yourself and others by observing all safety information. Failure to comply could result in personal injury and/or property damage! Save these instructions for future reference. Requirements ®...
- Page 2 INSTALLATION Mode Switching Summary For easy installation, select an existing light operated TEST Move ON-TIME Switch by a wall switch for replacement. to 1, 5, or 20 minutes For best performance, mount the fixture about 8 ft. (2.4 m) above the ground. NOTE: If fixture is mounted higher than AUTO 8 ft.
- Page 3 Bulb Installation Mount the Light Control NOTE: When re-lamping, turn power off and let the ❒ Place the mounting bolt through the front of the fixture cool. junction box cover. Push the small gasket hole over ❒ To remove lamp shade, loosen set screw 2 full the mounting screw.
- Page 4 TEST AND ADJUSTMENT NOTE: If fixture is mounted higher than 8 ft. (2.4 m), aiming the sensor down will reduce coverage distance. ❒ Turn on the circuit breaker and light switch. The detector is less sensitive to motion directly towards it. NOTE: Sensor has a 1 minute warm up period before it will detect motion.
- Page 5 SPECIFICATIONS Horizontal Range ..Up to 70 ft. (21 m); 100 ft. (30.5 m) with Range Boost. [var ies with surrounding temperature] Vertical Range ..Up to 15 ft. (4.6 m) Sensing Angle ..Up to 240° horizontal. Up to 80° Vertical Electrical Load .
- Page 6 Manual de Instrucciones y Partes 2LBL3, 2LBL4 Por favor lea y guarde estas instrucciones. Léalas cuidadosamente antes de intentar armar, instalar, operar o dar mantenimiento al producto descrito. Protéjase Ud. y los otros observando toda la informa- ción de seguridad. ¡Si no lo hace podría ocasionar lesión al personal y/o daño al equipo! Guarde estas instrucciones para referencia futura.
- Page 7 INSTALACION Resumen de las modalidades del interruptor Para una fácil instalación escoja una luz con un PRUEBA interruptor de pared. Mueva el interruptor de Para un mejor funcionamiento, instale el aparato a casi tiempo (ON-TIME) a 1, 5 2.4 m del suelo. NOTA: Si el aparato está instalado a ó...
- Page 8 Instalación de bombilla Instale el control de luz ❒ Ponga el perno de montaje a través del frente de NOTA: Cuando cambie la bombilla, apague la energía la tapa de la caja de empalme. Empuje el agujero y deje que el aparato se enfríe. pequeño de la empaquetadura sobre el tornillo de ❒ Para quitar la pantalla de la lámpara afloje el tornillo montaje.
- Page 9 PRUEBA Y AJUSTE NOTA: Si el aparato está instalado a más de 8 pies (2,4 m), si se apunta el detector hacia abajo se reducirá la ❒ Prenda el cortacircuitos y el interruptor de luz. distancia de cobertura. El detector es menos sensible del movimiento que se NOTA: El detector tiene un período de cerca de 1 dirige hacia él.
- Page 10 ESPECIFICACIONES Requisitos de energía . 120 VCA, 60 Hz Fases de Operación . . PRUEBA, AUTOMATICO y Alcance horizontal ..Hasta 70 pies (21 m), Aumento MODO MANUAL de Distancia prendido. Hasta Retardo de Tiempo . . . Ajustable de 1, 5 ó 20 minu- 100 pies (30.5 m), Aumento de Distancia apagado.
- Page 11 Mode d’emploi et guide des pièces 2LBL3, 2LBL4 Veuillez lire et conserver ces directives. Lisez-les attentivement avant de commencer à assembler, installer, utiliser ou entretenir le produit qui y est décrit. Assurez en outre votre protection et celle des autres personnes qui vous entourent en respectant toutes les consignes de sécurité. Le fait de ne pas le faire pourrait entraîner de graves blessures ou des dommages.
- Page 12 INSTALLATION PRIORITÉ MANUELLE Le mode manuel ne fonctionne Pour faciliter l’installation, choisir un appareil d’éclairage que la nuit parce que la lumière devant être remplacé et qui est déjà commandé par un du jour remet le capteur en interrupteur. mode AUTO. Pour assurer un rendement optimum, monter le luminaire à...
- Page 13 Installation de l’ampoule Montage de la commande d’éclairage NOTE: Avant de remplacer une ampoule, couper l'ali- ❒ Insérer la vis de montage dans le trou du couvercle mentation et attendre que l'appareil refroidisse. de la boîte de jonction. Pousser le petit trou de la ❒...
- Page 14 ESSAIS ET RÉGLAGES NOTE : Lorsque le luminaire est installé à une hauteur supérieure à 8 pi (2,4 m), le fait de diriger le détecteur ❒ Mettre en circuit le disjoncteur et l’interrupteur vers le bas réduit la portée de la couverture. d’éclairage.
- Page 15 FICHE TECHNIQUE Courant requis (lampes éteintes) . . . 120 V c.a., 60 Hz Portée ... 21 m avec amplification de portée Modes de hors circuit et de 30,5 m losqu’en fonctionnement .
- Page 16 NOTES / NOTAS _____________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ ___________________________ 598-1325-00 Get user manuals: See SafeManuals.com...