Chicago Pneumatic CP86150 Mode D'emploi page 6

EN
English
Technical Data (See right figure)
Dimension
capacity
[kg]
A
[mm]
B
[mm]
C
[mm]
F
[mm]
E
[mm]
F1
[mm]
F2
[mm]
R
[mm]
M
[mm]
oil
[l]
Weight
[kg]
max. pressure
[MPa]
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
Machine type(s)
• The machinery described is intended for machinery production and assembling spare parts. It is used to press, size, assemble, rivet small parts in
process No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.
Mounting instruction
Make sure every parts are fixed and tightened.
• Attach the base section to the frame (Fig.03) and support to left and right connecting plate. (Fig. 04)
• Assemble the nylon ring to gauge fitting, then put the pressure gauge and twist tight. (Fig. 05/06)
• Remark: twist as tight as possible, otherwise it will be leak. Attach the gauge fitting to the suitable upper cross beam and twist bolt.
• Assemble pump to the frame and hose kit to the pump Fig. 07 (CP86150), Fig. 09 (CP86200), Fig. 11 (CP86300 & CP86500).
• Insert the complete handle into the opening of the lever support.
• During moving the machine, make sure to use the proper lifting equipment and follow the instructions in document 8940174875 <INSTRUCTIONS
FOR MOVING THE TABLE>
• Main structures of PRESS include Pin, Feet, V-Block, Table, Frame. (Fig. 02)
Caution
Working area of 1 m must be kept free both in front of and behind the machine while it is in operation so that it
is always easily accessible (Fig.12)
Be careful then use the PESS, SAFETY INSTRUCTIONS in document 8940174875 .(Fig.14)
Purge air from the hydraulic system:
• Open the air valve by turning it counterclockwise and purge the air bleed valve (Fig. 09)
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
• Pump several full stokes to eliminate any air in the system.
Operation
Caution
Ensure table at proper position and lock the table by 4 pins firmly. (Fig.15)
• Close the release valve, by turning it clockwise.
Note : Press has an Automatic 2-speed hydraulic pump, equipped with an automatic valve instead of an control valve.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
• Pump the handle/foot pedal until serrated saddle nears workpiece.
Align workpiece and ram to ensure center loading.
Caution
A single hand-wheel controls the release valve, the switching between fast and slow speed can be done
automatically
• Pump the handle/foot pedal to apply load onto workpiece (see numeration in pressure gauge).
• When work is done, stop pumping, slowly and carefully remove load from workpiece by turning the release valve counterclockwise in small increments.
(must turn with the small angle)
• Once ram has fully retracted, remove workpiece from table.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
The V-block must be used by pair, not by piece!
Only one person is allowed to operate the press.
Make sure that the operator must wear protective cloth, gloves, safety helmet, shoes and ear protector
during operating.
To avoid accidents, always be aware of any on-going work on the machine. Also, always stay focused on
the job to be done.
CP86150 CP86200 CP86300
15 000 20 000 30 000
700 740 795
540 700 700
882 1772 1772
120 132 140
500 510 535
157 185 151
457 1175 1031
160 186 160
/ / 200
0,6 0,95 1,1
75,5 105 166,7
61 69 58
CP86150 / CP86200 / CP86300 / CP86500
CP86500
50 000
1030
800
1830
207
730
68
1048
200
245
2,5
298
62
Hydraulic press