Remington i-Light Prestige IPL6750 Mode D'emploi page 9

• If the attachment is removed while the unit is powered ON, all indicator lights on the base unit will flash and audible
"beeps" will sound.
• Allow the system to cool down for 5 minutes before attempting to change attachments.
• Turn the Power Switch OFF and unplug the Power Cord from the electrical outlet.
• Hold the attachment with one hand while pressing both Attachment Release Buttons with the other hand and pull
gently (Fig. 10).
• Gently push the other attachment back into the Hand Piece making sure both side tabs click into place.
• NOTE: the longer tab (with gold circuits) must be on top to properly fit.
• Store the unused attachment in a safe location (such as in the packaging) taking care not to damage the Flash
Window and other components.
• The i-LIGHT is equipped with two operating modes: Single Flash Mode and Multi-Flash Mode. Your i-LIGHT device
will automatically be set to Single Flash Mode each time the device is powered ON.
• Single Flash Mode: The i-LIGHT will flash each time the Flash Button is pressed. This mode is ideal for precision treat-
ments of the face and small areas.
• Multi-Flash Mode: The i-LIGHT device will flash when the Flash Button is pressed and will continue to flash every 3
seconds when the skin contact sensors are fully engaged. The Multi-Flash mode allows you to quickly treat large
areas by simply gliding the hand piece over the skin after each flash.
How to treat:
• Place the Flash Window firmly against the skin - ensure the Skin Contact Sensors are fully engaged.
• NOTE: When the Skin Contact Sensors are fully engaged you will hear a 'chirp' and the Bulb Status Indicator Display
will illuminate green.
• Press the flash button to deliver a flash. You should expect to see a bright flash of light (similar to a camera flash) and
you should feel a mild sensation of warmth.
• Move to the next area and treat in a grid like pattern to ensure full coverage of the treatment area.
• For Single-Flash Mode, press the Flash Button each time you move to the next area.
• For Multi-Flash Mode, keep your finger on the Flash Button to keep it depressed and glide to the next area being
sure to keep the Skin Contact Sensors fully engaged. The next flash will be delivered automatically after 3 seconds.
• NOTE: During Multi-Flash Mode if you let go of the Flash Button or lose skin contact, simply resume treatment by
repeating the above steps.
Facial Treatment (female use only)
• Facial hair can be very different to body hair and the skin on the face tends to be sensitive and more likely to be
exposed to the sun's UV rays; therefore treating unwanted facial hair is different to treating the body – please be sure
to read the Warnings and Safety Precautions carefully before beginning a facial treatment.
• IMPORTANT: The Facial Attachment has been specially designed to treat the unique characteristics of female facial
hair. DO NOT use the Body or Bikini attachments on the face. See section 'Changing Attachments' for more informa-
tion.
• The Facial Attachment is only intended for use on female facial hair below the cheekbone (Fig. 2).
• DO NOT use on male beards or facial hair as the results may be permanent or uneven which may produce changes in
facial hair characteristics which may not be desirable.
TREATMENT TIPS
Body Treatment
• For best results, avoid overlapping flashes. This helps prevent exposure to more energy than is necessary to suppress
hair growth. It also ensures that you get the maximum use of the Bulb.
• For the most effective results, always use the highest intensity operating mode that does not cause discomfort on
the skin. The level you use should feel warm on your skin, but should never cause discomfort.
• You may notice that bony areas, such as elbows, shins and ankles, are more sensitive during treatment. This is normal
and should not be cause for alarm. To avoid this sensitivity, try stretching the skin away from the bony area during
treatment.
ENGLISH
GB
DE
NL
FR
ES
IT
DK
SE
FI
PT
SK
CZ
PL
HU
RU
TR
RO
GR
SI
HR
UA
AE
9