Publicité
Liens rapides
Vettis™
Model/Modelo/Modèle
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
Read all instructions prior to installation.
Lea todas las instrucciones antes de
hacer la instalación.
Veuillez lire toutes les instructions avant
l'installation.
For product & installation questions, do not return to the store. For additional help, contact customer service.
Si tiene preguntas sobre el producto y su instalación, no acuda a la tienda. Para ayuda adicional, comuníquese con el departa-
mento de servicio al consumidor.
Si vous avez des questions au sujet du produit et de l'installation, ne retournez pas au magasin. Pour obtenir de l'aide, commu-
niquez avec le service à la clientèle.
www.brizo.com
SINGLE HANDLE LAVATORY FAUCET
92171
ROBINET À UNE MANETTE POUR
LAVABO
LLAVE DE LAVABO CON MEZCLADOR
65088LF-p
65088LF-p-ECO
1
3/32" (2.5 mm)
?
www.brizo.com
1-877-345-BRIZO (2749)
brizosupport@brizo.com
01/29/2019 Rev. D
Publicité
Manuels Connexes pour Brizo Vettis 65088LF Serie
Sommaire des Matières pour Brizo Vettis 65088LF Serie
- Page 1 Si tiene preguntas sobre el producto y su instalación, no acuda a la tienda. Para ayuda adicional, comuníquese con el departa- 1-877-345-BRIZO (2749) mento de servicio al consumidor. Si vous avez des questions au sujet du produit et de l’installation, ne retournez pas au magasin. Pour obtenir de l’aide, commu- brizosupport@brizo.com...
- Page 2 You may need: Optional/Optional/Optional Usted puede necesitar: Articles dont vous pouvez avoir besoin: 3/32” (2.5 mm) Add optional temperature ring by removing cap button (1), set screw (2), handle (3) and bonnet cap (4). Install temperature ring (5), ensure that ring is aligned with the open notch on faucet.
- Page 3 METAL POP-UP / DESAGÜE AUTOMÁTICO DE METAL / RENVOI MÉCANIQUE EN MÉTAL SEALANT OVERTIGHTEN SELLADORES APRIETES DEMASIADO PRODUITS TROP SERRER D’ÉTANCHÉITÉ NOTE: If you determine the PEX supply tubing for this faucet is too long and must be shorter to create an acceptable installation, follow the instruction for Custom Fit Connections.
- Page 4 Turn faucet handle all the way on. Turn on hot and cold water supplies and flush water lines for one minute, check all connections at arrows for leaks. Retighten Slide finial (1) into slot in rear of faucet (2). Insert lift rod (3) through guide hole if necessary, but do not overtighten.
- Page 5 CUSTOM FIT CONNECTIONS / CONEXIONES ESPECIALES / SPÉCIAUX TUYAUTERIE BRANCHEMENT Installer accepts the responsibility to cut supply tubing in a way that allows a leak-free joint to be created. Brizo is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. Must use RP50952 sleeves supplied with model and nuts included on supply lines.
- Page 6 CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. LIMPIEZA Y CUIDADO DE SU LLAVE Tenga cuidado al ir a limpiar este producto.
- Page 7 Vettis™ RP92354 Lift Rod & Finial Models/Modelos/Modèles Barra de Alzar y Pomo RP92769-1.5gpm 65088LF-p & 65088LF-p-ECO Tige de Manoeuvre et RP92770-1.2gmp-ECO Grain de la Tirette Flow Regulator Restrictor de flujo Limiteur de débit RP92349 RP92353p Valve Cartridge Handle Assembly Cartucho de la Válvula Ensamble de la Manija Cartouche Poignée...
- Page 8 RESULTING FROM REASONABLE WEAR AND TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE are not covered by this warranty. Brizo Kitchen & Bath Company shall not be liable for any damage to the product PRODUCT FOR AN UNINTENDED APPLICATION, FREEZING WATER, ABUSE, NEGLECT OR IMPROPER...