Publicité
Liens rapides
www.videolarm.com
F D W 7 5
Fusion Dome (Outdoor Wall Mount with Housing)
Installation and Operation Instructions for the following models:
FDW75C2N
IP Network Ready 7" Outdoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.
FDP75C2N
IP Network Ready 7" Outdoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera,120 to 24Vac transformer.
IFDW75CN
IP Network Ready 7" Indoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.
IFDP75CN
IP Network Ready 7" Indoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera,120 to 24Vac transformer.
FDW75C2NE
IP Network Ready 7" Outdoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera. (European Model)
FDP75C2NE
IP Network Ready 7" Outdoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera. (European Model)
FDW75C2N/AC
IP Network Ready 7" Outdoor dome hsg w/wall mount, clear acrylic dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.
FDP75C2N/AC
IP Network Ready 7" Outdoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/
blower, fan an IP Network PTZ camera,120 to 24Vac transformer.
B e fo re a t te m p t i n g to co n n e c t o r o p e ra te t h i s p ro d u c t,
p l e a s e re a d t h e s e i n s t r u c t i o n s co m p l e te l y.
All manuals and user guides at all-guides.com
81-IN5358R1
Publicité
Manuels Connexes pour Moog Videolarm FDW75 Serie
Sommaire des Matières pour Moog Videolarm FDW75 Serie
- Page 1 All manuals and user guides at all-guides.com www.videolarm.com F D W 7 5 Fusion Dome (Outdoor Wall Mount with Housing) Installation and Operation Instructions for the following models: FDW75C2N IP Network Ready 7” Outdoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/ blower, fan an IP Network PTZ camera, 120 to 24Vac transformer. FDP75C2N IP Network Ready 7”...
- Page 2 All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. 1 Read Instructions - All the safety and operating Keep these instructions. instructions should be read before the unit is CAUTION CAUTION operated.
- Page 3 All manuals and user guides at all-guides.com LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows: PRODUCT CATEGORY PARTS LABOR All Enclosures and Electronics Three (3) Years Three (3) Years Pan/Tilts Three (3) Years **6 months if used in autoscan...
- Page 4 All manuals and user guides at all-guides.com Electrical Specifications Contents of Box FDW75 Power 24VAC Class 2 Only 24 VAC 26 Watts Accessories: Heater: 25 Watts, Blower: 1 Watt Camera Power: 40 Watts Max Tools Required: .100” Flat Head Screwdriver Phillips Head Screwdriver English 24 VAC...
- Page 5 All manuals and user guides at all-guides.com WALL MOUNTING Securely mount unit to wall or to appropriate If using conduit connect, connect to adapter bracket. incoming conduit fitting. • Monte con seguridad la unidad a la pared o al • Si usa el conducto conecte, conecte con la guar- soporte apropiado del adaptador.
- Page 6 All manuals and user guides at all-guides.com FOR PENDENT/ WALL MOUNTING Wrap Teflon tape around the pipe threads Securely mount bracket to wall. Pull wiring to ensure a tight seal. through bracket and position grommet as shown. • Con seguridad soporte del montaje a emparedar. Tire del cableado •...
- Page 7 All manuals and user guides at all-guides.com Loop the lanyard over the set screw to Make the appropriate wiring connections temporarily hold housing. from the dome to the gooseneck. • Coloque el acollador sobre el tornillo de presión para • Haga las conexiones apropiadas del cableado de la bóveda celebrar temporalmente la cubierta.
- Page 8 All manuals and user guides at all-guides.com RJ45 24VAC POWER Camera Max 40 Watts Camera Orange Heater/Blower Yellow 26 Watts Heater/Blower Green Alarm 1 Blue Alarm 2 Violet Alarm 3 Gray Common White Make the appropriate male and female connections. Indoor model does not include pre-run cables. •...
- Page 9 All manuals and user guides at all-guides.com Axis 213 (3) #8x3/8” ½" 2539 Mounting Plate Captive Screw 1" 2" Mounting Mounting Hole Hole Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8”...
- Page 10 All manuals and user guides at all-guides.com Axis 215 (3) #8x3/8” 1" Captive Screw 1" MOUNTING HOLE MOUNTING HOLE 2" AXIS215-VL3026 Install the camera to the mounting plate with (4) #8 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Page 11 All manuals and user guides at all-guides.com AXIS 231-232D Axis 231D/232D Mounting Hole Loosen Screw Mounting Mounting Hole Hole Loosen the screw to the right of the tab by Use the (3) keyhole slots indicated above. approximately (5) turns. • Utilice (3) las ranuras del ojo de la cerradura indicadas •...
- Page 12 All manuals and user guides at all-guides.com Connection Module Screw Power Board Remove the power board located inside the housing. Attach the connection module as shown. This is what the typical path of illumination will look like with the setting at 30 degrees. Attach this assembly to the housing using (1) 6-32x3/8”...
- Page 13 All manuals and user guides at all-guides.com Axis 233D Mounting Hole Power Board Mounting Hole Disconnect the orange, red, and black wires. Remove the Use the holes indicated above to mount power board in the housing by loosening screws on the the camera.
- Page 14 All manuals and user guides at all-guides.com Quick Release Plate Additional Spacers Keyhole Slots Camera Bracket Base Bracket Mount the Axis 233D camera bracket and quick release plate using the additional spacers from This is what the typical path of illumination will look like with the setting at 30 degrees. the hardware packet.
- Page 15 All manuals and user guides at all-guides.com Canon VB-C10R ½" 2539 Mounting Plate Captive Screw 1" 2" Mounting Mounting Hole Hole Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8 Phillips head screws on the top of the spacer as shown above.
- Page 16 All manuals and user guides at all-guides.com Canon VC-C4R/VC-C50IR (3) 8 x 32 x 3/8 1" 2539 Mounting Plate Mounting Hole Captive Screw 1" 2" Mounting Hole Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8 Phillips head screws on the top of the spacer as shown above.
- Page 17 All manuals and user guides at all-guides.com Elmo PTC-201 2539 Mounting Plate Mounting Hole Captive Screw ½" 2" Mounting Hole Place the camera onto the quick release bracket using the (4) metric 3M Phillips head screws provided. Place the screws on the spacers. Slide on the plate and camera then secure. •...
- Page 18 All manuals and user guides at all-guides.com Elmo PTC-401 2539 Mounting Plate Mounting Hole Quick release 1" plate Captive Screw 2" Mounting Hole Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 19 All manuals and user guides at all-guides.com JVC VN-C625U / TK-625U 1" Mounting 2630 Mounting 1" Hole Plate Remove the cover and detach bracket. Attach (4) 1” spacers to the 2630 mounting plate and (4) to the main bracket. Place (3) 8x32x3/8” Phillips screws onto the spacers. Secure plate and camera. •...
- Page 20 All manuals and user guides at all-guides.com Panasonic BB-HCM381/580/581 & KX-HMC280 ½" 2539 Mounting Plate 1" 2" Mounting Hole Install the camera to the bracket with the 1/4x20” washer and lock washer. Place (3) 8x32x3/8” screws on the spacers. Slide on the camera and plate then secure. •...
- Page 21 All manuals and user guides at all-guides.com Sony SNCRZ25 Mounting Hole 1" 2539 Mounting Plate Mounting Hole Attach bracket with (1) 1/4x20 bolt, washer and lock washer and (2) 3mm x 8mm Phillip head screws and lockwashers. Place the screws on the spacers. Slide on the plate and camera then secure. •...
- Page 22 All manuals and user guides at all-guides.com Sony SNCRZ50 Mounting Hole ½" 2" 2539 Mounting Mounting Hole Plate Attach bracket with 3mm x 8mm bolts and lock washers. Place (3) 8x32x3/8”screws on the spacers. Slide on the plate and camera then secure. •...
- Page 23 All manuals and user guides at all-guides.com Before After Loop the lanyard around the tab inside the Align the arrows on the outside of the dome housing. and lock. • Alinee las flechas en el exterior de la bóveda y •...
- Page 24 All manuals and user guides at all-guides.com Replacement Parts List FDW75 1 1 1 Part Number Description RPFD7501 LOWER TRIM RING FD7T TINTED REPLACEMENT CAPSULE FD7C CLEAR REPLACEMENT CAPSULE RPFD703 DOME CLAMPING BRACKET RPFD072 24 VAC HEATER RPFD080 (12 VDC) BLOWER (USED IN 24V HOUSINGS) RPFD060 CAMERA BRACKET RPFD050 (MODEL FD7HB)
- Page 25 All manuals and user guides at all-guides.com Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry. Should a problem arise, rest assure that Videolarm stands behind its products by offering some of the most impressive warranty plans available: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on...