Publicité
Les langues disponibles
Les langues disponibles
#04649 CPBMADP and #04671 CPBMADP29
MILWAUKEE
®
1. Remove the battery from the grinder before any work
is to be done on the grinder.
2. Remove wax protective coating on the new router bit. The
router bit is not supplied with CPBMADP beveler adapter
and must be purchased separately.
3. Place the router bit into the grinder collet and slide the bit
down until it stops (bottoms out) and hand tighten the collet.
4. Next, raise the bit up until the unfinished shaft is just visible
above the collet. Tighten the collet with the wrenches
provided with the grinder.
5. FIRMLY TIGHTEN THE COLLET to prevent the router bit from
coming loose while operating and causing damage or injury.
6. Place the beveler adapter head #04649 or #04671 onto the
grinder locating the Adjusting Knob 90° to the left of the on/
off switch as shown in the Assembly Diagram 1.
7. Loosen the Adjusting Knob and slide the Guide Plate to the
lowest position. Push down on the Adapter Head with a
rocking motion until the top of the guide plate is in line with
the bottom of the Router Bit.
8. Slide the guide plate assembly up and tighten the clamp
ASSEMBLY DIAGRAM 1
screw on the Adapter Head.
9. Adjust the guide plate to the desired length of bevel and
tighten the Adjusting Knob.
SHROUD
GUIDE PLATE
FOR INTERNATIONAL USE
To replace Metric collet with Imperial collet*:
1. Remove collet nut and collet
2. Remove old collet from collet nut
3. Insert new collet into collet nut
4. Replace collet nut and collet onto tool
*The metric collet supplied with some international Milwaukee die
JUSTING KNOB
ST BE LOCATED
grinder models will not fit the REED RBIT1 and RBIT2. A change
° FROM SWITCH
of collet is required; REED offers #04686 CPBMCOLLET. Refer to
AS SHOWN
die grinder operator's manual for further instructions.
MILWAUKEE
GRINDER
INTERNAL BEVEL SHROUD:
An internal shroud #94644 is available for beveling 2" ID and
larger pipe. This shroud can be used on all REED Bevel Boss
models.
REPLACE SHROUD:
To replace the shroud, remove the three screws from the guide
plate with provided 1/8" hex wrench, replace shroud and
reassemble.
READ AND UNDERSTAND ALL SAFETY WARNINGS AND
INSTRUCTIONS, INCLUDING DEWALT/ MILLWAUKEE
GRINDER AND BATTERY CHARGER WARNINGS AND
INSTRUCTIONS.
FAILURE TO FOLLOW ALL WARNINGS AND INSTRUCTION
LISTED MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR
SERIOUS PERSONAL INJURY.
ASSEMBLY:
GUIDE PLATE
SHOULD BE FLUSH
WITH BOTTOM OF
ROUTER BIT
CLAMP SCREW
ADAPTER HEAD
FITS MILWAUKEE
®
04649, 04671 ASSEMBLY DIAGRAM 1
GUIDE PLATE
ADJUSTING KNOB
MUST BE LOCATED
90° FROM SWITCH
AS SHOWN
04649, 04671 ASSEMBLY DIAGRAM 2
APPROXIMATE
#04686 Collet
4 REFERENCE LINES
1/8" INCREMENTS
FOR ADJUSTING
THE BEVEL SIZE
1/8"
ASSEMBLY DIAGRAM 1
SHROUD
MILWAUKEE
GRINDER
ASSEMBLY DIAGRAM 2
LOCATE ROUTER BIT SO
THE UNFINISHED AREA ON
THE SHAFT IS JUST ABOVE
TOP OF COLLET
5/32"
COLLET
OPERATING DIAGRAM
RBIT2
RECOMMENDED:
SET HEIGHT TO THIS LINE
FOR REMOVING HALF THE
MATERIAL FOR FIRST PASS
ON LARGER BEVEL
WHEN USING RBIT2
04649, 04671 - CPBDKIT
Adapter Plate (Millwaukee)
GUIDE PLATE
SHOULD BE FLUSH
WITH BOTTOM OF
ROUTER BIT
CLAMP SCREW
ADAPTER HEAD
FITS MILWAUKEE
®
POWER SOURCE
Die
Uses
Brand
Grinder
Adapter
Model
Head
Milwaukee
2784-22
04649
®
Milwaukee
2784-20
04649
®
Milwaukee
2984-20
04671
®
Milwaukee
2939-20
04671
®
3
0523-54654
4 REFE
1/8"
FO
TH
Publicité
