Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
π
H-10161
WALL MONITOR MOUNT –
17-50" FULL MOTION
TOOLS NEEDED
Electric
Phillips Head
Drill
Drill Bit
Phillips
Tape Measure
Screwdriver
Adapter x 4
Monitor Plate x 1
A5
Spacer x 4
Cable Management
Clip x 1
CAUTION! This product is designed to be
installed on solid concrete walls or drywall
with wood studs. Before installing, make sure
the wall will support the combined load of the
equipment.
CAUTION! Be careful not to scratch the monitor
screen during assembly.
ATTACHING TO WALL
CONCRETE WALL
1. Align wall plate in desired location. Place level on
top of the wall plate to ensure it is leveled correctly.
Mark where holes for screws are to be located.
(See Figure 1)
PAGE 1 OF 12
1-800-295-5510
uline.com
3/16" Drill Bit
4 x 4 mm Allen Wrench
3/8" Drill Bit
5 x 5 mm Allen Wrench
(included)
Magnetic Level
(included)
Stud Finder
PARTS
Wall Plate x 1
B4
B3
M6 Nut x 2
Washer x 3
INSTALLATION
Pour le français, consulter les pages 9-12.
13 mm Socket
B1
A6
Lag Screw x 3
A1
Square
Washer x 4
M4 x 20 mm Bolt x 4
A3
M6 x 6 mm
M6 x 20 mm Bolt x 4
Bolt x 8
Figure 1
Level
Wall
Plate
Para Español, vea páginas 5-8.
Two-Person Assembly
Recommended
B2
Plastic Anchor x 3
A2
M5 x 20 mm Bolt x 4
A4
M8 x 20 mm Bolt x 4
Concrete
Wall
0223 IH-10161
Publicité
Sommaire des Matières pour Uline H-10161
- Page 1 Para Español, vea páginas 5-8. Pour le français, consulter les pages 9-12. π H-10161 1-800-295-5510 uline.com WALL MONITOR MOUNT – 17-50" FULL MOTION TOOLS NEEDED Electric Phillips Head 3/16" Drill Bit 4 x 4 mm Allen Wrench Drill Drill Bit 3/8"...
- Page 2 INSTALLATION CONTINUED 2. Drill holes 2⁄" deep using 3/8" drill bit. Insert plastic anchors (B2) into pre-drilled holes. (See Figure 2) Figure 4 Wood Stud Figure 2 Concrete Wall Wall Plate 2⁄" Stud Finder 3/8" 3. Drill holes 2⁄" deep using 3/16" drill bit. (See Figure 5) NOTE: It is recommended to use a masonry drill bit for concrete walls.
- Page 3 INSTALLATION CONTINUED ATTACHING MONITOR PLATE 2. Determine bolt size that is compatible with monitor. Using the square washers (A6) and spacers (A5), Determine the hole pattern on the back of the install the monitor plate to the monitor. monitor. If the hole pattern is larger than the monitor plate, the monitor adapters must be attached using SQUARE WASHER M6 x 6 mm bolts (B4).
- Page 4 Figure 11 Monitor Figure 12 5 x 5 mm Allen Wrench M6 Nut Tension Screw 90º – -2º–12º Wall Plate Monitor Plate 90º – 180º – 3º – M6 Nut Cable Management Clip 1-800-295-5510 uline.com PAGE 4 OF 12 0223 IH-10161...
- Page 5 Para Español, vea páginas 5-8. Pour le français, consulter les pages 9-12. π H-10161 800-295-5510 uline.mx SOPORTE DE PARED PARA PANTALLA – MOVIMIENTO TOTAL DE 17-50" HERRAMIENTAS NECESARIAS Taladro Broca Broca de 3/16" Llave Allen de 4 x 4 mm Eléctrico...
- Page 6 CONTINUACIÓN DE INSTALACIÓN 2. Perfore orificios de 2⁄" de profundidad utilizando la broca de 3/8". Inserte los taquetes de plástico (B2) en Diagrama 4 los orificios preperforados. (Vea Diagrama 2) Viga de Madera Diagrama 2 Pared de Concreto Placa para Pared Detector de 2⁄"...
- Page 7 CONTINUACIÓN DE INSTALACIÓN FIJAR LA PLACA PARA MONITOR 2. Determine el tamaño de perno compatible con el monitor. Usando las rondanas cuadradas (A6) y los Determine el patrón de orificios en el respaldo del separadores (A5), instale la placa para monitor al monitor.
- Page 8 Llave Allen de 5 x 5 mm Tuerca para Tuerca M6 Tensión 90º – -2º–12º Placa para 90º Pared – Placa para 180º – Monitor 3º – Clip para Tuerca M6 Organizar Cables 800-295-5510 uline.mx PAGE 8 OF 12 0223 IH-10161...
- Page 9 H-10161 1-800-295-5510 uline.ca SUPPORT MURAL À PLEIN MOUVEMENT POUR MONITEUR – 17 À 50 PO OUTILS REQUIS Perceuse Mèche de perceuse Mèche de perceuse de 3/16 po Clé Allen de 4 x 4 mm électrique cruciforme Mèche de perceuse de 3/8 po Clé...
- Page 10 INSTALLATION SUITE 2. Percez des trous de 2 ⁄ po de profondeur en utilisant une mèche de perceuse de 3/8 po. Insérez les Figure 4 ancrages en plastique (B2) dans les trous prépercés. Colombage en (Voir Figure 2) bois Figure 2 Mur en Plaque béton...
- Page 11 INSTALLATION SUITE FIXATION DE LA PLAQUE DE MONITEUR 2. Déterminez la taille des boulons compatibles avec le moniteur. Installez la plaque sur le moniteur avec Déterminez le schéma des trous à l'arrière du les rondelles carrées (A6) et les espaceurs (A5). moniteur.
- Page 12 5 x 5 mm Vis de réglage de tension Écrou M6 90º – -2º à 12º Plaque 90º – 180º Plaque de – murale 3º moniteur – Pince de gestion Écrou M6 des câbles 1-800-295-5510 uline.ca PAGE 12 OF 12 0223 IH-10161...