Silverline 827819 Mode D'emploi page 5

827819
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust-related hazards
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly
maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained
Battery & Battery Charger
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger
before attempting to charge the battery
• Do not attempt to use the charger with any batteries other than those
supplied. Keep the battery charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these instructions may
cause overheating or fire
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries
provided with this power tool, or others recommended by the supplier.
Keep batteries clean; foreign objects or dirt may cause a short. Allow
batteries to cool for 15 minutes after charging or heavy use. Failure to
follow these instructions may cause overheating or fire
• When not in use, batteries should be stored in a dry place, near to room
temperature (20˚C). Ensure that batteries cannot accidentally short in
storage
All manuals and user guides at all-guides.com
Multi-Cutter Safety
• Take care to avoid hidden wiring and piping when using this tool
• Contact with electric or gas lines can lead to fire, electric shock and
explosions. Penetrating a water line can result in damage to property and
electric shock. Use appropriate detectors to determine if utility lines are
hidden in the work area
• If a cutting accessory makes contact with a 'live' wire, the exposed metal
parts of the power tool may become 'live' and could give the operator an
electric shock. Hold the power tool by the insulated gripping surfaces at
all times during use
• Keep your workplace clean. Blends of materials are particularly
dangerous. Dust from light alloys can burn or explode
• Do not scrape wet or damp materials (eg wallpaper) or use this tool on
moist surfaces. Penetration of water into the machine increases the risk
of electric shock
• Do not treat the work surface with fluids containing solvents. When
materials become warm from scraping, toxic vapours may develop
• Use this tool for dry sanding only. Penetration of water into the machine
increases the risk of an electric shock
• Secure the workpiece with a clamp or vice
• Keep hands away from the cutting range
• Do not reach under the workpiece. Contact with the blade can result in
serious injury
• Wear protective gloves when changing application tools/accessories.
Application tools/accessories become hot after prolonged usage
• Hold the tool firmly with both hands
• Exercise extreme caution when handling this tool
Product Familiarisation
1 Accessory Clamp Bolt
2 Drive Plate
3 Guide Light
4 Contoured Grip
5 LED Screen
6
On/Off Button
7
+ Button
8 - Button
9 Battery Pack
10 Battery Charge Level Indicator Button
11 Charger
www.silverlinetools.com
10.8V Multi-Cutter
5