SYNQ AUDIO RESEARCH DMC-1000 Mode D'emploi page 10

ENGLISH
KEY LOCK SW/LED
< >
SW/LED(Fx SYNC)
SW/LED(¼)
<
> SW/LED(4/1)
SW/LED(VINYL)
WHEEL MODE
SW/LED(10)
TEMP RANGE
1 SW/LED/LED2
2 SW/LED/LED2
3 SW/LED/LED2
4 SW/LED/LED2
½(RED) LED
1(RED) LED
2(RED) LED
4(RED) LED
8(RED) LED
16(RED) LED
½(GREEN) LED
3/4(GREEN) LED
1/1(GREEN) LED
2/1(GREEN) LED
TEMP RANGE 6 LED
TEMP RANGE 16 LED
LOOP SET LED
A.CUE SCRATCH LED
CDJ LED
SW
DISC EJECT
SGL/CTN SW
TIME SW
SHIFT SW
ENTER SW
<< SW
>> SW
CUE PLAY SW
TAP SW
SW
PITCH BEND -
SW
PITCH BEND +
SYNQ 15/139
®
OPERATION MANUAL
1E/1E 5D/1E
0C/0C 4B/0C
19/19 58/19
12/12 51/12
24/24 63/24
2A/2A 69/2A
14/14/31 53/14/31
1A/1A/32 59/1A/32
20/20/33 5F/20/33
26/26/34 65/26/34
35 35
36 36
37 37
38 38
39 39
3A 3A
3B 3B
3C 3C
3D 3D
3E 3E
3F 3F
40 40
41 41
42 42
43 43
0D 4C
01 40
1F 5E
45 --
16 55
1C 5B
22 61
28 67
07 46
03 42
09 48
DMC1000
ENGLISH
CC-ABSOLUTE (VR)
Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC
controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value
from 0x00 to 0x7F, directly related to the location of the controller.
CC-RELATIVE (ENC)
Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus
the controller MIDI ID is indicated with the channel along with the CC number. The value 0x40 is the
reference value of the controller. This is an offset to 0x40 "one's complement" notation.
A message with data 0x43 indicates a positive change of 3.
A messages with data 0x31 indicates a negative change of 9.
SWITCH ON/OFF (SW,CENTER,CW,CCW)
These messages are used for switches.
Control Change messages are sent with status 0x9n, SWITCH On and Off value are 0x7F and 0x00,
where n is the channel.
LED ON/OFF (LED)
These messages are used for LED.
Control Change messages are sent with status 0x9n, LED On and Off value are 0x7F and 0x00, where n
is the channel.
INSTALLING THE Q-DBASE SOFTWARE
The DMC1000 works perfectly without the Q-DBASE database files but if you want to search your tracks
easily and lightning fast than you should install the Q-DBASE software on your computer! Please note that
the program currently only works under Windows (XP, Vista, Win7). To be sure that you always have the
latest version, you can download the software from our website. Installing the program is very easy: just
double-click the file and follow the instructions on your screen.
USING THE Q-DBASE SOFTWARE
Each time you add or remove tracks from your USB hard disk,
you must run the Q-DBASE software again to update the database files!
After the installation you will see a new program directory called
"SYNQ". In this directory you will find 2 files:
- Uninstall (to uninstall the software)
- Q-DBASE (to start the software)
 Connect your USB-hard drive to your PC and check which drive
letter was assigned to it.
 Click on the Q-DBASE icon to start the software: the main screen is
shown.
 In the upper left corner choose your USB-drive.
 Press the BUILD-button on the right side.
 The software starts scanning the USB-drive for compatible
audio files and extracts the ID3-tags to build the Q-DBASE files,
needed to speed up the search function on player. Once the
progression bar on the bottom is full, the database building
process is finished and a short summary is shown.
 The program wrote the Q-DBASE files (file extensions: .DBH + .dat
+ .DBX) to the USB-drive so now you can remove it from your PC
and connect it to the DMC-1000.
To achieve the best results, please always use the latest version of
the database software. You can find the software version at the
bottom left of the "About" screen.
SYNQ 16/139
®
OPERATION MANUAL
DMC1000