Delabie SPEEDJET 2 Manuel D'instructions page 4

OPERATION
• The hand dryer is supplied in the "ON" position.
• Device is activated after a few seconds (internal test of correct operation
is carried out).
• Insert hands completely in the opening: automatic activation following
detection of hands by sensors (fig. A).
• During operation a countdown of seconds, represented with bars, takes place
(fig. B). The red LED lights up.
• Stops automatically when hands are removed or after 12 seconds of drying.
Stops automatically in the event of continued use longer than 30 seconds.
The blue LED lights up.
• The hand dryer is equipped with an evaporation system which detects
the presence of water and activates an element to evaporate it.
TECHNICAL FEATURES
• Low energy consumption: 1,050W in mode without heating,
1,550W with heating.
• 230V~ / 50Hz.
• Air flow rate: 61 l/s. Air speed: 540 km/h.
• Acoustic level: 66 dBA.
• Class II, IP21.
• The sensitivity of sensors can be adjusted by setting the potentiometers
situated inside the hand dryer (fig. C).
INSTALLATION AND ELECTRICAL CONNECTION
The electrical connection should be carried out before fixing the hand dryer
to the wall.
• Switch off the product before using.
• Remove the cover (fig. D), pass the mains power supply cable like
H05RN - F2 x Ø 1.5mm (not supplied) through the hole (fig. E) and screw
it to the connection lead.
• Fix the cable holding piece to prevent it coming off as a result of pulling.
• The installation must comply with the current regulations and guidelines
of the country of installation.
• Recommended installation height (distance between floor and top of device):
A - 95cm for adults, 85cm for children and disabled people (fig. F
• Drill the wall before installing the support plate. Fix the plate to the wall
with the rawl plugs provided (fig. F
and rawl plugs depending on the wall type.
• Attach the hand dryer to the wall plate (fig. G), remove the filter then fix
the 2 screws to the lower part and put the filter back.
• To put in ON/OFF mode, remove the screws a from both sides
of the hand dryer and reposition the cover  (fig. H).
• Activate the product by connecting it to the electrical network.
REMINDER
• Our products must be installed by professional installers in accordance
with current regulations and recommendations in your country, and the
specifications of the engineer.
• Avoid splashes inside the mechanism of the hand dryer.
• Do not shake the hand dryer.
• In the event of disfunction, immediately turn the hand dryer off and contact
our After Sales Support Team.
• Do not install the hand dryer outside or on a flammable surface.
SETTINGS
If when activating the hand dryer, the detection of hands is deemed to be
inadequate, it is possible to adjust:
- remove the cover and screws from both sides of the hand dryer a (fig. H);
- slide the cover upwards to remove it  (fig. H);
- adjust the sensors' sensitivity using the potentiometers  and  by turning
clockwise or anti-clockwise to reach the desired setting (fig. C).
All manuals and user guides at all-guides.com
1
). If necessary use different screws
2
EN MAINTENANCE (FIG. B)
The hand dryer is equipped with alarms for the notification of required
maintenance:
+1: the HEPA filter is full. Change it by removing the fixing cover of the filter
held by 2 screws (fig .I).
+2 fixed: the temperature is too high, automatically preventing the
evaporation system. Contact our After Sales Support Team.
+2 intermittent +4 fixed: the evaporation system is not able to cool down
correctly. Contact our After Sales Support Team.
+2 intermittent +4 intermittent: a heating problem hinders the correct
functioning of the evaporation system. Contact our After Sales Support Team.
+4 intermittent: the evaporation system has been running for more
than 5 hours.
+3: the carbon from the motor is at the end of its life and must be changed.
Once the maintenance has been carried out, restart the motor counter in
order to know the date the carbon will need to be changed. Press the restart
button .
An object prevents the hand dryer from stopping for longer than 30 seconds.
The hand dryer stops automatically.
Once the object is removed, the operation will restart automatically.
Automatic elimination of residual water with evaporation and sterilisation: system
without the need for a water collection tank or water runoff on the floor or walls.
MAINTENANCE & CLEANING
The hand dryer is equipped with alarms for the notification of required servicing.
• Clean regularly using a soft damp cloth. Never use abrasives, scouring powder
or any other chlorine, acid or alcohol-based products.
• Clean the infrared sensors' glass regularly.
• Ensure the channel is clean and not obstructed by any substances or impurities.
• Keep the suction area clear.
• Clean the opening for hands regularly and completely.
Product conforms to current European Directives.
).
For the UK market only: Tel. 01491 821 821 - email: technical@delabie.co.uk
The installation guide is available on: www.delabie.co.uk
For all other markets: Tel. +33 (0)3 22 60 22 74 - email: sav@delabie.fr
The installation guide is available on: www.delabie.com
After Sales Care Support:
EN