Publicité
Les langues disponibles
Les langues disponibles
SYMBOLS
Read the manual
Warning
Double insulation
Wear eye protection
OPERATING INSTRUCTION
Always make sure the power tool is isolated from the power supply before fitting any attachment
Handle. See
Always make sure the fixed handle is secure before any job takes place as a loose handle could invite
injuries.
Switching the chisel on/off
The chisel has an On/Off switch built in to the handle. Holding the chisel with both hands simply
squeeze the trigger and the motor will start. To switch off release the trigger.
WARNING
The electric hammer chisel continues for a few second after the trigger has been release, be careful when
putting it down.
Fitting a chisel bit into the Hex housing
To insert the bit, hold the front cover rotate the stop lever 180º as arrow 2 in a clockwise direction as arrow 1,
while pulling the stop lever towards you, Insert the bit you want to use to the hex housing, the shank of the
bit has a cut out hold the bit with its flattened part upwards, push the bit into the hex housing as arrow 3
Put the bit into the hex housing and clamp the bit by turning the stop lever half a turn anti clockwise. This
will lock the bit in place.
Do not use the chisel until you are satisfied the bit is secured. This electric hammer chisel does not have
reverse direction, so always take care not to force the chisel in case the chisel bit gets stuck. Always make
sure you keep the chisel going in and out to remove debris. This chisel does not have torque facility. It is
not recommended to use any other bit other than masonry or chisels do not use metal cutting drills, this
could cause serious injury NOTE: chiseling for an extended period of time may cause the chisel motor to
overheat. If the chisel gets hot, stop chiseling and allow it to cool for at least 15 minutes. Precautions on
using electric hammer chisel.
1. Before using the electric hammer chisel always makes sure the oil supply is to the full level and the
screw is tight.
2. This electric hammer chisel has a fixed handle always make sure the screws holding the handle are
secure before operation takes place. Always use both hands when using this chisel failure to adhere to this
could invite injuries.
3. Safe operation, always make sure you have a stable posture and safe footing before operating the electric
hammer chisel.
4. When working at a high level, always make sure that no person or persons are below you, as this could
invite injuries to those persons under you.
5. Before starting any job like breaking, chipping a wall, floor or ceiling, thoroughly confirm that no items
such as an electric cable, water pipe or conduit are buried inside as this could cause injury or flooding.
6. Properly set the bit holder.
7. The bit can become very hot during operation exercise extreme caution as this could cause injury.
8. Always wear protective safety glasses
4
All manuals and user guides at all-guides.com
Wear ear protection
Wear dust mask
Do not dispose of old appliances in the
household garbage
Keep your hands and feet away from all
opening
GB
9. Always wear ear defenders or earplugs
10. Always wear suitable dust mask
11. Always wear protective footwear.
12. Always wear hardhat
Information on how to use the electric hammer chisel
Prior to operation
1. Power source Ensure that the power source to be utilized conforms to the power requirements specified
on the product nameplate.
2. Power switch Ensure that the power switch is in the off position before any work is carried out on the
chisel. If the plug is connected to a power receptacle while the power switch is in the on position, the
power tool will start operating immediately this could invite serious injury.
3. Extension cord.
When the work area is away from the power source, use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as practicable
How to use the electric hammer chisel
Place the bit you are going to use to do the job in hand as in Fig 2
(1) Pull the trigger switch after applying the chisel bit tip to the chiseling position.
(2) It may be necessary to punch the bit against the crushing position forcibly in order to begin the striking
stroke. This is not due to malfunction of the tool, it means that the safe guard mechanism against no-load
striking is working.
(3) By utilizing the weight of the machine and by firmly holding the hammer chisel with both hands, one
can effectively control the subsequent recoil motion.
Proceed at a moderate work rate; the use of too much force will impair efficiency.
CAUTION
Sometimes the tool does not begin the striking stroke even when the motor rotates this may be because
the oil has become thick
Due to low temperature or has been standing idle for long period. Run the chisel for approx 5 minutes to
bring the oil temperature up.
CLEANING AND MAINTANCE
Oil feeding
Caution!
Prior to oil feeding, always disconnect the plug from the power supply receptacle. Since an oil chamber is
built in this electric hammer chisel, it can be used for approximately 20 days without supplying lubrication
oil, assuming that the chisel is used continuously 3–4 hours daily.
Feed oil into the oil tank as described below before using the hammer chisel.
(1) When the chisel is held upright look through the oil gauge window to see if oil is visible, if no oil shows
oil must be installed before operating.
If chisel is used without oil this could seriously damaged the chisel and forfeit any warranty given.
(2) Before feeding oil, use the provided wrench to remove the oil gauge (4). Be careful not to lose the
rubber packing attached below the oil gauge.
(3) Check the oil level once daily, confirming that oil is filled.
(4) After feeding oil, securely clamp the oil gauge.
Note: Oil for the electric hammer chisel is sold separately, use Shell oil ROTELLA 40 (engine oil) or
equivalent, this is sold at most shops or filling stations anywhere.
Maintenance and inspection
1. Inspecting the tool
When using dull tool bits this can cause motor malfunction and degraded efficiency. Always replace dull bits
with new ones without delay when abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure to do so could result in serious injury.
3. Maintenance of the motor.
The motor unit winding is the very "heart" of the power tool. Exercise due care to ensure the winding does
GB
5
Publicité
