ENGLISH
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for sanders
Warning! Contact with or inhalation of dusts arising
x
from sanding applications may endanger the health of the
operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and
fumes and ensure that persons within or entering the
work area are also protected.
Thoroughly remove all dust after sanding.
x
Take special care when sanding paint which is possibly
x
lead based or when sanding some woods and metal
which may produce toxic dust:
– Do not let children or pregnant women enter the work
area.
– Do not eat, drink or smoke in the work area.
– Dispose of dust particles and any other debris safely.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
x
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
x
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-on button
3. Dust extraction outlet
4. Sanding base
5. Paper clamp lever
6. Variable speed control knob
7. Dustbag
4
All manuals and user guides at all-guides.com
Assembly
Warning! Make sure that the tool is switched off and
unplugged.
Fitting sanding sheets (fig. A & B)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (fig. A)
Make sure that the tool is switched off and unplugged.
x
Press the sheet firmly and evenly onto the sanding base
x
(3), making sure that the holes in the sheet line up with
the holes in the base.
Fitting regular sanding sheets (fig. B)
Make sure that the tool is switched off and unplugged.
x
Soften the sanding sheet by rubbing its non-abrasive side
x
over the edge of a worktop.
Press the paper clamp levers (4) upwards to release them
x
from the retaining grooves and open the paper clamps by
pressing them down.
Place the sheet onto the sanding base, making sure that
x
the holes in the sheet line up with the holes in the base.
Insert the edge of the sanding sheet into the front paper
x
clamp as shown.
Press the front paper clamp lever (4) downwards and
x
locate it in the retaining groove.
While keeping a slight tension on the sheet, insert the
x
rear edge of the sheet into the rear paper clamp.
Press the rear paper clamp lever (4) downwards and
x
locate it in the retaining groove.
Fitting and removing the dustbag (fig. C)
Fit the dustbag (7) over the dust extraction outlet (3).
x
Rotate the dustbag to lock it into position.
x
To remove the dustbag, proceed in reverse order.
x
Connecting a vacuum cleaner (fig. D)
Insert the adaptor (8) into the dust extraction outlet (3).
x
Connect the hose (9) of the vacuum cleaner to the adaptor.
x
Use
KA197E - Variable speed control
The variable speed control allows you to adapt the speed of
the tool to the workpiece material.
Set the control knob (6) to the desired setting. Use a high
x
speed for wood, medium speed for veneer and synthetics
and low speed for acrylic glass, non-ferrous metals and
for removing paints.