Publicité
Les langues disponibles
Les langues disponibles
Fascia
Toyota Avalon view
Hitch Shown In Proper Position
Equipment Required: Strap or bungee
cords to support exhaust
Fastener Kit: 36514F
Wrenches: 10mm, 12mm, 14mm,
17mm, 6" socket extension, 11/16"
Drill Bits: ¼", 1", ½"
Side
specific
Vehicle
support
bracket
B. Align block
A. Insert bolt and
on access hole
Block into frame
Figure 2
j
Qty. (4)
Hex bolt M10 X 1.25 X 40 CL8.8
k
Conical washer 3/8"
Qty. (4)
l
Qty. (2)
Carriage bolt 7/16-14 X 1.5 GR5
m
Qty. (2)
Spacer
1.
Remove appearance panel and return panel to owner.
2.
Lower exhaust by removing two bolts at the end panel and two bolts on the frame rail exhaust hanger bracket each side. End panel bolts to be
reinstalled.
3.
Support the exhaust to prevent damage using straps, bungee cords or other means. Remove 1
passenger side of the exhaust and the next 2
4.
Remove heat shields.
5.
Raise (slide) hitch into position over exhaust pipes and temporarily install M10 hex bolts for support. Exhaust hanger bracket not necessary at
this step.
Using the hitch as a template mark and center punch the (1) holes on both sides. Drill ¼" pilot hole both sides.
6.
Lower hitch and drill 1" hole in frame rail. Mark and drill heat shield for the 7/16 carriage bolt using the frame rail as template. Set aside for later
7.
install.
8.
Insert carriage bolt and spacer into the frame as shown leaving pull wire attached. See Figure 2.
9.
Raise hitch into position threading the pullwire through the bracket. Install at least one M10 bolts as shown both sides.
10. Remove pullwire and install conical washers and nuts on both side. Center hitch and Torque 7/16" fasteners to required specification. Install
heat shield.
11. Install the 1
st
& 2
nd
forward rubber isolator brackets.
12. Remove M10 bolts and install the exhaust hanger brackets thru the forward weld nut both sides (item 1).
13. Install vehicle support bracket re-using the existing end panel bolts and (item 1) remaining M10 bolts.
14. Tighten all fasteners to the required torque specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle
and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
©
2011, 2013 Cequent Performance Products, Inc
Installation Instructions
Toyota Camry
Toyota Avalon
Drawbar Kit:
36071
Drawbar must be used in the
RISE position only.
Toyota Avalon install
1" hole to be
drilled both sides
Forward weld nut
Existing M10
weld nuts
End panel
bolts
p
C. Pull bolt
thru block
Note: Fasteners typical both sides of hitch.
nd
forward rubber isolator bracket.
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
page 1
page 2
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
l
m
n
o
Exhaust hanger
k
bracket
j
Figure 1
n
Conical Washer 7/16"
Qty. (2)
o
Qty. (2)
Hex nut 7/16-14
p
Qty. (2)
Pullwire 7/16
q
Qty. (2)
Hex bolt M6 X 1.0 X 40
st
rubber isolator bracket on the forward
Sheet 2 of 6
36514N
Part Numbers:
36514
90079
06139
Accessory Rating
Wiring Access Location: PC3 & 4
Frame rail
nd
2
Forward rubber
Heat
isolator bracket
shield
location
Drill ½" to ¾" hole
st
1
Forward rubber
isolator bracket
location
q
Forward
4-25-13
Form F206 Rev A 5605
B
Rev. D
Publicité
