LEGION LIGHTING Goose Neck 9103 Serie Guide D'installation Rapide

CAUTION:
1. Read all instructions before starting installation.
2. This product must be installed in accordance with the applicable installation
codes by a qualified electrician familiar with the construction and operation of
the product and the hazards involv
3. Disconnect power at circuit breaker of fuse before starting installation.
4. To avoid injury, wear gloves during installation.
5. To reduce the risk of electrical shock and product damage, do not install this
luminaire during rain or other storms.
6. Do not test luminaire using an electric generator before installation.
WARNING:
MIN 75°C SUPPLY CONDUCTORS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED
This is a high-quality commercial grade product and is equipped with a 0-10V dimming
driver. A 0-10V dimmer is required to use the dimming feature of this product. 0-10V
dimmer come equipped with 2 wires specifically for dimming which are typically violet
and gray. DO NOT use a standard (2-wire) wall dimmer with this product.
Accessories
AA: BB: CC: DD:
Mounting Screws (2) Mounting Screws (2) Wire Nuts (3) Screw Caps (2)
8-32UNC x 32 8-32UNC x 32 P4 (10 mm x 22 mm) (Customization)
Lenght: 1.25" or 31.75 mm Lenght: 3/8" or 9.525 mm
D: Swivel
C: Arm
E: Set Screw
EE: A: Lamp
Mounting Bracket (1)
(Customization )
B: Lamp Shade
Installation
PULL THE WIRE OUT FROM JUNCTION BOX
Pull the supply wire (Line, Neutral and Ground) out from the JUNCTION BOX in the wall through
the large center hole in the MOUNTING BRACKET (EE). (Figure 1)
ATTACH MOUNTING BRACKET
Attach MOUNTING BRACKET (EE) to the Junction BOX using the MOUNTING SCREWS (AA).
(Figure 2)
AA
BB
Mounting
Bracket (EE)
Junction Box
Figure 1
Installation
ATTACH WALL CANOPY
Place the WALL CANOPY over the JUNCTION BOX and onto the fixture's MOUNTING SCREWS
(BB) and adjust the fixture MOUNTING SCREWS (BB) until they protrude out an appropriate
height from the back of the WALL CANOPY to allow the SCREW CAPS (DD) to hold the WALL
CANOPY tightly against the wall. Remove the WALL CANOPY and secure the position of the
MOUNTING SCREWS (BB) against the MOUNTING BRACKET (EE). (Figure 3)
ADJUST FIXTURE ANGLE
Following the arrow illustration to rotate swivel and butterfly bolt to adjust fixture angle which
you want.
Butterfly Bolt
Legion Lighting Co., Inc. | 221 Glenmore Avenue, Brooklyn, NY 11207 | Phone: 718-498-1770 | Fax: 718-498-0128
Toll Free: 1-800-4-LEGION | email: sales@legionlighting.com |
Installation
PRE-ASSEMBLE FIXTURE
Connect Arm (C) and Lamp (A) through Swivel (D) and rotate Swivel to fasten two parts.
Be careful not to misplace any of the hardware needed for installing the fixture.
C: Arm
D: Swivel
A: Lamp
E: Set Screw
B: Lamp Shade
Installation
ATTACH POWER SUPPLY WIRE
1. Connect the fixture ground wire (GREEN) to the ground supply wire using a wire nut (CC).
2. Connect the BLACK fixture wire to the BLACK (Line) supply wire using the wire nuts (CC).
3. Connect the WHITE fixture wire to the WHITE (Neutral) supply wire using the wire nuts (CC).
4. Carefully tuck all wiring back into the JUNCTION BOX, making sure there are no exposed
un-insulated wires. (Figure 3)
W all Canopy AA
DD BB
Mounting
Bracket (EE)
BLACK Fixture Wire
Junction Box WHITE Fixture Wire
Fixture Ground Wire
Wire Nuts / Connector (CC)
Figure 2 (GREEN)
Figure 3
Installation
ATTACH WALL CANOPY
For additional sealant, apply waterproof silicone to the gap between the wall canopy and wall.
Figure 4
www.legionlighting.com
Series 9103
Junction Box
Neutral Supply Wire
(WHITE)
Line Supply Wire
(BLACK)
Ground Supply Wire