AirKing AK965L Manuel D'opération

Ventilateur d'évacuation
Masquer les pouces Voir aussi pour AK965L:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

IMPORTANT INSTRUCTIONS -
: AK965L, AKF965
Models
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
electric shock and injury to person, including the following:
1. Read all instructions before installing or using exhaust fan.
2. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer.
3. Before servicing or cleaning the unit, switch power off at
service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the
service panel.
4. Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
and standards, including fire-related construction.
5. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent back drafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA)
and the American Society for Heating, Refrigeration, and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
CAUTION:
FOR GENERAL VENTILATING USE ONLY. DO
NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS
AND VAPORS.
210575006 Rev. B 10-06
OPERATING MANUAL
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
SAVE THESE INSTRUCTIONS
6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. This unit must be grounded.
9. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off
power unit.
WARNING:
DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL
DEVICE.
WARNING:
A SHOWER STALL ENCLOSURE.
10. Do not install into a ceiling thermally insulated to a value
greater than R-40.
11. NEVER place a switch where it can be reached from a tub or
shower.
WARNING:
WARNING:
A SUPPLEMENTAL HEATER FOR USE WITH A TIMER OR A
SWITCH. IT IS NOT INTENDED TO BE USED AS THE PRIMARY
SOURCE OF HEAT AND CONTROLLED BY A THERMOSTAT.
www.airkinglimited.com
Exhaust Fan
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
DO NOT INSTALL OVER A TUB OR MOUNT IN
DO NOT USE IN KITCHENS.
THIS UNIT IS DESIGNED AND TESTED TO BE
1 of 12

Publicité

Table des Matières
loading

Sommaire des Matières pour AirKing AK965L

  • Page 1 IMPORTANT INSTRUCTIONS - OPERATING MANUAL : AK965L, AKF965 Exhaust Fan Models READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
  • Page 2 INSTALLATION INSTRUCTIONS SECTION 2 New Construction CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. Mounting Rail Installation: Install the rails on the housing and position the housing next to the joist. Line up housing so it will be SECTION 1 flush with the finished ceiling.
  • Page 3 1a. Mounting Tab Installation: Position housing against the joist and the junction box. The neutral (white) wire from the home is not trace an outline of the housing onto the ceiling material (Figure 7). connected to the switch or junction box, but will be run to the unit’s Set housing aside and cut opening, being careful not to cut or wire compartment.
  • Page 4 Install the appropriate bulbs (not included) specific to your model: the two tabs of the light lens and pulling outward from lens. The AK965L: Install a 100 watt maximum, type A19 medium base lens will swing open on the connector bars. DO NOT remove the incandescent bulb (not included) and a 7 watt maximum type lens from the grill (Figure 12).
  • Page 5: Troubleshooting Guide

    Refer to instructions in Section 6 Completing the Installation , to reinstall grill. Night Light (AK965L, AKF965): Unscrew night light bulb from socket and replace with a 7 watt maximum type C7 (candelabra Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently base) night light bulb.
  • Page 6: Replacement Parts Diagram

    REPLACEMENT PARTS DIAGRAM Qty. Description Replacement Part # Qty. Description Replacement Part # Fan Housing 5S3402039 Lamp Holder - AK965 5S3402054 Mounting Rails 5S1299002 Lamp Holder - AKF965 5S1201025 Collar Screw 5S3402040 Reflector 5S3402055 Collar 5S3402041 Grill 5S3402056 Damper 5S3402042 Lens Frame 5S3402057 Motor - Vent...
  • Page 7: Instructions Importantes - Manuel D'opération

    INSTRUCTIONS IMPORTANTES – MANUEL D’OPÉRATION : AK965L, AKF965 Ventilateur d’Évacuation Modèles LIRE ET CONSERVER CES INSTRUCTIONS LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ. FAILLIR À SE CONFORMER AUX INSTRUCTIONS PEUT RÉSULTER EN BLESSURE PERSONNELLE GRAVE ET/OU EN DOMMAGE À...
  • Page 8: Traverses De Montage

    INSTRUCTIONS D’INSTALLATION SECTION 2 Nouvelle Construction AVERTISSEMENT: VOUS ASSURER QUE L’ALIMENTATION EST COUPÉE AU PANNEAU DE SERVICE AVANT DE COMMENCER Installation des Traverses de Montage: Installer les traverses sur L’INSTALLATION. le châssis et positionner le châssis près de la solive. Aligner le châssis pour qu’il soit à...
  • Page 9: Interrupteur

    1a. Installation des onglets de montage: Positionner le châssis contre terre (vert ou cuivre nu) de la résidence à la boîte de jonction. Le la solive et tracer un contour du châssis sur le matériau du plafond fil de neutre (blanc) de la résidence n’est pas connecté à (Figure 7).
  • Page 10 Les lentilles basculeront en position ouverte sur les barres connecteurs. NE PAS enlever les lentilles AK965L: Installer une ampoule incandescente à culot moyen de la grille (Figure 12). de type A19 de 100 watts au maximum (non-comprise) et une ampoule d’un maximum de 7 watts (culot de type candélabre)
  • Page 11: Guide De Dépannage

    Onglet en position ouverte sur les barres connecteurs. NE PAS enlever les lentilles de la grille (Figure 16). Ampoule Incandescente (AK965L): Dévisser le globe du socle Figure 16 de lampe et le remplacer avec une ampoule incandescente d’un maximum de 100 watts, de type A19 à culot moyen.
  • Page 12: Diagramme Des Pièces De Remplacement

    DIAGRAMME DES PIÈCES DE REMPLACEMENT # de pièce # de pièce Qté. Description de remplacement Qté. Description de remplacement Cabinet du ventilateur 5S3402039 Support de la Lumière - AK965 5S3402054 Traverses de Montage 5S1299002 Support de la Lumière - AKF965 5S1201025 Vis à...

Ce manuel est également adapté pour:

Akf965Ak965fl

Table des Matières