Sola Hevi Duty SDP Serie Guide Rapide

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Technical Data
Input
115/230 VAC universal
•
Nominal voltage:
(SDP4 auto select)
•
Power factor (PFC): as required to meet EN61000-3-2
Output
• 24V (22.5-28.5VDC Adj.)
Nominal voltage:
•
Power boost: 1.4x nominal current for 2 sec.
•
Holdup time: > 25ms at Full Load (25˚C)
• Tolerance: < ±2 % overall
Line regulation <0.5%
Load regulation <0.5%
Time & temp. drift <1%
•
Initial voltage setting: 24.5V ± 1%
•
Ripple: < 50mVpp
• Power back immunity: > 35V
Jumper Selectable Via Front Panel
• Parallel Operation:
(SDP4 Only)
• Over voltage protection: < 33VDC
Standards, Certifications
EMC
Emissions EN 61000-6-3, Class B EN55011, EN55022 Radiated
Conducted including Annex A
Immunity EN 61000-6-2, EN61000-4-2 Level 4, EN61000-4-3 Level 3,
EN61000-4-6 Level 3, EN61000-4-4 Level 4 input and level 3
output. EN61000-4-5 Isolation class 4, EN61000-4-11,
Transient protection according to VDE 0160/W2 over entire load
range.
Approvals EN60950, UL508 Listed, cULus, UL 60950, cURus, CE (LVD
73/23 & 93/68/EEC), (EMC 89/336 & 93/68/EEC). EN61000-3-2,
EN60079-15 (Class 1, Division 2 hazardous location, Groups A,
B, C, D w/ T3 temp class up to 60˚C Ambient.) UL60950 testing
to include approval as NEC Class 2 power supply acc. To NFPA
70 art. 725-41 (a)(2).
Environmental Data
Ambient temperature
•
Storage/Shipment -25˚C...+85˚C
•
Full nominal load -10˚C...+60˚C
• Derated +60˚C...+70˚C
Degree of protection IP20 (EN60529), Protect the unit from moisture (and
condensation)
Installation
Fusing
Input Internally fused.
Output Outputs are capable of providing high currents for short periods
of time for inductive load startup or switching.
Mounting Simple snap-on to DIN TS35/7.5 or TS35/15 rail system. Unit
should handle normal shock and vibration of industrial use and
transportation without falling off the rail.
Connections Input/Output: screw terminals, connector size range: 20-12AWG
(0.5-2.5mm2) for solid conductors.
This equipment is suitable for use in Class 1, Division 2, Groups A,B,C,D or non-
hazardous locations only
WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability
for Class 1, Division 2.
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has
been switched off or the area is known to be non-hazardous.
DIN Rail Mounting Montaje en Riel DIN
Snap on the DIN Rail: Atorar en en Riel DIN:
1. Tilt unit as 1. Incline la unidad
illustrated como se ilustra
2. Put it onto the DIN 2. Póngala sobre el Riel
Rail DIN
3. Push downwards 3. Empuje hacia abajo
until stopped hasta que se
detenga
4. Push at the lower
front edge to lock 4. Empuje de la parte
baja del frente para
5. asegurar
Shake the unit
slightly to ensure
that the unit is 5. Mueva la unidad
secure ligeramente para
verificar está segura
SDP Series
Power Supplies
Technical Services
SDP06-24-100T
SDP1-24-100T USA (800) 377-4384
SDP2-24-100T International (847) 679-7800
SDP4-24-100T
www.solaheviduty.com
Rev. 09/24/03
Monture du Rail DIN
Poser le Rail DIN:
1. Faire pivoter
l'appareil comme
illustré
2. Poser sur le Rain
DIN
3. Enfoncer jusqu'à
arrêt
4. Appuyer sur le bord
inférieur pour fixer
5.
Vérifier que l'appareil
est bien fixé