Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
O
p
e
r
O
p
e
r
T
a
m
p
e
r
S
w
i
t
c
h
T
a
m
p
e
r
S
w
i
t
c
h
The Siren is protected by a tamper switch which will be activated
if the Siren is cover opened. When installing the Siren, please
make sure the tamper switch is properly compressed against the
front cover.
Before installing the Siren, changing mounting location or
batteries, please make sure to disable the tamper switch
temporarily using your Control Panel's Siren Tamper function and
enable the tamper switch again after finish working on the Siren.
Please refer to your Control Panel manual for detail.
S
i
r
e
n
A
u
d
i
b
l
e
P
e
r
f
o
r
m
a
S
i
r
e
n
A
u
d
i
b
l
e
P
e
r
f
o
r
m
a
The Siren produces a minimum of 104 dBA sound pressure at 1
meter range when activated.
For Burglar and Panic Alarm, the Siren gives a continuous alarm
sound.
For Fire / Water alarm, the Siren gives an intermittent alarm
sound of 2-sec siren followed by a 1 sec interval.
The Siren is silenced when either the programmed siren length
expires or when the Control Panel is disarmed to turn off the Siren.
Please refer to Dip Switch table above to set your desired alarm
length through Dip Switch SW3 and SW4 setting.
Audio Status Indication Table
The Siren will sound indication beeps according to different status,
please refer to table below.
Arm/Home
Disarm
Arm (Low Battery)
Disarm (Low
Battery)
Arm (Tamper)
Disarm (Tamper)
Previous alarm
warning
Entry/Exit Sound
* Siren Audio indication will be effected by the Confirmation
ON / OFF setting in your Control Panel settings.
B
B
a
a
t
t
t
t
e
e
r
r
y
y
The Siren uses four 1.5V D alkaline batteries as its power source.
It also features low battery detection function to notify the Control
Panel when battery voltage is low.
When the Siren is on low battery, follow the procedure below to
change the batteries.
1. Temporarily disable the Siren's tamper protection function
(please refer to your Control Panel manual for detail). The
Siren will sound a beep to indicate the tamper is disabled.
2. Remove the front cover.
3. Remove the four screws fixing the battery compartment and
take off the compartment lid.
4. Remove the old batteries and press the Tamper Switch twice
to discharge.
5. Insert the new D cell alkaline batteries into the battery
compartment according to correct polarity.
6. The Siren will emit beeps when the last battery is inserted.
7. Replace the battery compartment lid and front cover
8. Enable the tamper protection function through your Control
Panel. The Siren will sound a beep to indicate.
a
t
i
o
n
a
t
i
o
n
n
c
e
n
c
e
S
i
r
e
n
A
u
d
i
o
S
i
r
e
n
A
u
d
i
o
1 beep*
2 beeps*
5 beeps
5 beeps
5 beeps
2 beeps*
3-second beep
Count-down beeps
S
S
p
p
e
e
c
c
i
i
f
f
E
n
v
i
r
o
n
m
e
n
t
a
l
C
o
n
d
i
t
i
o
E
n
v
i
r
o
n
m
e
n
t
a
l
C
o
n
d
i
t
i
o
-10°C to 40°C, relative humidity 85% non-condensing.
R
R
a
a
d
d
i
i
o
o
868 MHz
i
i
c
c
a
a
t
t
i
i
o
o
n
n
n
n
Publicité
Table des Matières
