Safety Advice; Maintenance Instructions - puris Bad Linea 050 Instructions De Montage

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 7

sAFeTY ADVIce

• The mounting must only be done by experts.
• Please read through the mounting instructions carefully
before mounting in the bathroom.
• Warning: defective mounting is dangerous!
• check whether the wall is suitable for the mounting and
that the fasteners are strong enough for the forces involved.
• The enclosed fastening material is only suitable for solid walls
of sufficient load-bearing strength.
• If the nature of the wall is different (e.g. plasterboard or
lightweight walls), a different fastening which is suitable for
the load should be chosen by the customer.
electrical installations should only be carried out by a
specialist electrician DIN VDe 0100-701 (VDe 0100-701):2008-10.
• electrified, mirrored cabinets and flat mirrors must be located
at a minimum distance of 600 mm away from the bath or
shower.
• The safety regulations and standards of the particular coun-
tries must be observed.
IMPOrTANT INFOrMATION
• Inspect the packaging for external damage when it is delivered.
• Please check the number of bathroom cabinets supplied and
the associated sets of ironmongery (screws, cover caps,
handles, etc.) against the delivery note or the article's label
on the packaging.
• Caution: only remove the protective caps on the mirrored
cabinet's doors after mounting the doors, in order to avoid
damaging edges of the mirrors.
• Use suitable spacers or distance blocks to even out the exist-
ing differences in level caused by coverings applied to the
walls, e.g., partial tiling.
• reinforce any walls of insufficient load-bearing strength.
• The drilled dimensions are measured from the FFL according
to the dimensioned layout.
• Always fasten the hanging bar to the wall with 2 screws!
• Fasten the cabinets with the suspension rails:
- tall cabinets (600 mm width)
- Shelf
- Washstand vanity unit at 700 mm (hangers differ for widths
1000 mm and 1700 mm
- Base cabinet, Highboard mit drawer system
• Pay attention to the different hanging widths of the mirror
cabinet
• The horizontal spacing between the cabinets can be chosen
freely.
TOOLS
• Drill and battery-operated screwdriver
• Stone drill bit of 8 mm dia.
• Wood drill bit of 4 mm
• Folding metre rule and measuring tape
• Spirit level
• screwdriver with a 3.5 mm tip for Phillips screws
• screw clamps
• Pencil
• Silicone sealant (transparent and solvent-free)
Linea
keeP THe INsTrucTIONs IN A sAFe PLAce
i
Caution: keep the instructions safely because they contain
information about installing and operating the products.

MAINTENANCE INSTRUCTIONS

• Caution: do not use any chemicals, aggressive detergent
paste or scouring powder.
• The best way of cleaning the cabinet is to use a damp cloth
with some mild washing-up liquid.
• Take care that no residue from droplets remains on the lower
edge of bathroom cabinets.
• Polish the mirror with a damp cloth or chamois leather.
• The washbasin can be easily cleaned with any of the usual,
non-abrasive cleaning agents.
• Ventilate regularly in order to prevent the mould from forming.
MOUNTING SEQUENCE
i
For the figures, see the attachment
1. Dismantle the doors (Fig. A)
2. Dismantle the drawers
· standard technology (Fig. A1)
· comfort technology (Fig. A2)
3. Mount the mirror grip (Fig. B)
4. Mount the lamps (Figs. C/C1/C2/C3/C4)
The mains wire should not be live!
5. Install cornice light (Abb C3)
6. Hang up the furniture
· Mirror cabinet
· Tall cabinets, upper cabinets, centre cabinets, Base cabinet
· Highboard
· Washstand vanity unit
· washstand
7. Align furniture (Figs. D/D1/D2)
8. Mount the washstand with the LED (Abb. E)
The mains wire should not be live!
9. Mount the washstand
· Fit the washstand (Fig. F)
· seal the washstand (Fig. F1)
10. Install the tap (Fig. G)
· Warning: Use the enclosed rubber seal.
· Do not overtighten the tap!
11. Screw on the shelf (Fig. H)
· Warning: Do not drill through the shelf!
· use the enclosed screws.
12. Mount the doors (Fig. I)
13. Mount the drawers
· standard technology (Fig. J)
· comfort technology (Fig. J1/J2)
14. Aligning the doors (Fig. K/K1/K2)
15. Align the drawers
· standard technology (Fig. L)
· comfort technology (Fig. L1/L2/L3)
5

Publicité

Table des Matières
loading

Table des Matières