IK METAL 3580M Feuille D'instructions page 9

3) Take the necessary precautions against misuse in the event of dangerous products.
4) Do not spray on persons, animals, electrical equipment and power lines, upwind or over water courses.
5) Repairs or modifi cations to the tank are not authorised.
6) The safety valve must not be blocked.
7) If the spray materials enter into contact with hydrogen peroxide or products with similar oxygen release, this may cause
pressure increases and produce an explosion. Never use these products.
8) Damaged parts or those that do not work must be replaced immediately by our Customer Service Department Service
or by an unauthorised Customer Service Centre.
9) Avoid nearby infl ammable sources.
10) Do not leave the apparatus pressurised or in the sun. Ensure that the apparatus does not overheat above the operating
temperature.
11) Never blow through the nozzles or valves with your mouth.
12) Use only the manufacturer's replacement parts and accessories.
13) We shall not be held liable for any damages whatsoever caused by the use of third-party parts.
14) When handling hazardous substances, use the appropriate personal protection equipment.
15) During pumping, take note of the gauge so as not to exceed to the max. spraying pressure. Completely depressurise the
tank before fi lling it up, after use and before performing any maintenance work.
WARRANTY
It is hereby warranted that from fi rst purchase and during the corresponding legal warranty period (max. 2 years) that this
apparatus is free from material and processing errors. If any errors are detected during the warranty period, the manufacturer
or distributor in your country shall repair or (in the manufacturer's opinion) entirely replace it or the damaged parts, without
charging the costs of labour and materials.
If so, it is requested that you immediately contact us in that regard. The apparatus's invoice or purchase receipt is required.
Wear and tear parts (joints, o-ring, washers etc) and defects caused by an improper use or on grounds of force majeure are
excluded from the warranty.
CE Declaration of Conformity
according to EC Machinery Directive 2006/42/EC, Appendix II, No. 1A.
We,
Goizper Group
c/Antigua 4
20577 Antzuola
Spanien
declare under our sole responsibility that the product high-pressure spraying device of the series 3580M from factory
number 1289536 in the version supplied complies with all relevant provisions of the Directive 2006/42/EC. Furthermore, the
device complies with the Directive 97/23/EC for pressure equipment.
Mikel Irizar, c/Antigua 4, 20577 Antzuola, Spain, is authorized to compile the technical documentation.
Antzuola, 11.01.2013
Mikel Irizar
Technical Manager
FR
1
Pulvérisateur conçu pour application d'huiles de décoffrage, huiles minérales de faible viscosité et produits chimiques employés
dans le secteur de la construction et d'alcalinité peu élevée (pH ≤ 9).
Avant toute utilisation, tenir compte des indications du fabricant du produit. Les pulvérisateurs doivent exclusivement être
utilisés en extérieur ou dans des pièces bien ventilées. Aucun effet nocif pour le dispositif n'a été détecté, au moment de la
fabrication de celui-ci, résultant de l'utilisation des produits pesticides autorisés par l'Agence fédérale allemande BVI.
Une utilisation inadéquate peut entraîner des risques pour la santé et l'environnement.
Dispositif inapproprié : pour pulvérisation de liquides infl ammables, de peroxyde d'hydrogène et autres produits provoquant un
dégagement d'oxygène similaire, de substances corrosives (certains produits désinfectants et d'imprégnation, acides, eau de
Javel), de liquides contenant de l'ammoniaque, de solvants et liquides contenant des solvants, de mélanges visqueux, collants
ou formant des résidus (peintures, graisses) ; pour une utilisation dans le domaine alimentaire.
N'utiliser en aucun cas : associé à des sources de pression extérieures ; pour le stockage et la conservation de liquides.