Using The Tft Monitor; Open/Close Tft Monitor; Tft Monitor Auto Open; Monitor Tilt Angle Adjustment - Jensen VM9510TS Guide D'utilisateur

USING THE TFT MONITOR

Open/Close TFT Monitor

Press the OPEN button (1) on the front panel or press the
( ) button (25) of the front zone remote control to open/
close the monitor.

TFT Monitor Auto Open

• If "TFT Auto Open" is "on" when the unit is turned on,
the monitor automatically moves to the last viewing
position.
• If "TFT Auto Open" is "off" when the unit is turned on,
press the OPEN button (1) or ( ) button (25) on the
front zone remote control to move the monitor into the
desired viewing position.

Monitor Tilt Angle Adjustment

A known characteristic of LCD panels is the quality of the
display in relationship to the viewing angle. The monitor
angle can be adjusted for optimum viewing using one of the
following methods:
• Press the ( ) or ( ) buttons (3, 4) on the front of the
unit to adjust the tilt angle of the screen one step at a
time.
• Press and hold the to adjust the tilt angle of the screen
one step at a time.

Rear Camera Mode

When the vehicle is placed in "Reverse", and an optional rear
camera is connected to the VM9510TS, the TFT monitor will
automatically switch to the camera input source.

Aspect Ratio

The following sources only have the WIDE and OFF aspect
ratio option: AM / FM Tuner, CD-DA, SD Card, DVD+R/RW,
DVD-R/RW and CD-R/RW with music files. Press the WIDE
button (28) on the remote control to adjust the aspect ratio as
follows:
FULL
The entire screen is extended
horizontally to the aspect ratio of 16 to
9. The extension ratio is the same at
any point.
WIDE
The screen is extended horizontally to
the aspect ratio of 16 to 9. The
extension ratio increases toward the
right and left ends of the screen.
NORMAL
The conventional display image has a
4 to 3 ratio of horizontal to vertical,
leaving a blank area on the right and
left sides of the display.
OFF

Image Setting

Video Output Format
Table 3 shows the video output format for each playing
source.
Table 3: Video Output Formats
Playing Source Video Output Format
TUNER RGB Mode
DVD RGB Mode
AUX IN CVBS Mode
CAMERA CVBS Mode
TV CVBS Mode
*CVBS – Composite Video Baseband Signal
Adjustable Parameters
While in DVD or TUNER mode, the only parameter that can
be adjusted is brightness (BRIGHT). To access "PICTURE",
"COLOR", "CONTRAST", and "TINT" you must be in AUX or
CAMERA mode.
10
NOTE: The default adjustment is "0" in PAL mode. Tint is
unavailable for adjustment.
Parameter Adjustment Procedure
1. Enter Picture Quality Setting mode:
Press the PIC button (24) on the remote or press and
hold the WIDE/PICTURE button (2) on the unit.
2. Select Item to Set:
Press the ( ) ( ) buttons (14, 22) on the remote or
press and hold the ( ) or ( ) buttons (18, 19) on the
front panel.
3. Set Parameters:
Press ( ) ( ) buttons (17, 19) on the remote or press
( ) ( ) buttons (8, 9) on the unit.
4. Exit Picture Quality Setting Mode:
Press the PIC button (24) on the remote or press and
hold the WIDE/PICTURE button (2) on the front panel.

Parking Brake Inhibit

• When the "PRK SW" cable is connected to the brake
switch, the display on the TFT monitor will display video
only when the vehicle is applied.
• Parking brake function is overridden when the video
source is set to CAMERA.
• When the parking brake inhibit is active, the front
monitor displays "Parking Is On", preventing the driver
from watching content while driving. Rear video screens
are not affected.

Monitor Movement Mechanism

If an obstruction occurs in the monitor path, the motion will
stop automatically to prevent damage to the mechanism or
monitor.
Normal operation is resumed by pressing the OPEN button
(1) or disconnecting and reconnecting the power.
VM9510TS