Télécharger Imprimer la page

Fortin DUO CAN 2 Guide D'installation page 4

Kit tous en un pour démarreur à distance alarme

Publicité

Les langues disponibles

Les langues disponibles

DUO CAN 2
Copyright © 2007, FORTIN AUTO RADIO INC
VEHICLE FIT GUIDE
Years
Vehicles
Véhicules
Années
Chrysler
02
03
04 05 06 07
08
Aspen
300
300C
Dodge
02
03
04 05 06 07
08
Caliber
Charger
Dakota
Magnum
Nitro
Ram
Jeep
02
03
04 05 06 07
08
Cherokee
Commander
Compass
Grand Cherokee
Patriot
Wrangler
CAN PROGRAMMING INSTRUCTIONS
1
Connector 1 (Black):
1.A
Determine the type of installation:
INSTALLATION WITH
INSTALLATION WITHOUT DATA-LINK (See page 2)
1.B
Connector 2 (White):
Make the connections page 2.
1.C
Connector 3 (White, located at the back of the module):
Make the connections page 2.
2
3
4
5
6
7
LOCK
UNLOCK
PANIC
TECHNICAL SUPPORT / INFORMATION
Neither the manufacturer or distributor of this module is responsible of damages of any kind
indirectly or directly caused by this module, except for the replacement of this module in
case of manufacturing defects. This module must be install by qualified technician. This
instruction guide may change without notice. isit www.ifar.ca to get latest version.
ALL RIGHTS RESERVED
Fonctionnal if equipped
DATA-LINK (See page 2 )
Press
the programming switch while
inserting the main wires harness (
into the CAN module.
The LED will illuminate to indicate you are in
programming mode, release the
programming button.
Connect
the other connectors
(
CONN. 2
)
WARNING: Connector 2 can be easily
plugged in backwards.
Connect
the other connectors
(
CONN. 3
)
Turn the key to the
"ON" position
Once the LED starts to flash rapidly
the key to the
OFF position
The LED will flash until you
press the
OEM remote lock button
.
The LED will turn off to indicate the
module has been programmed.
The CAN is now ready for use.
V
PATS
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
Purple/Brown
PATS PROGRAMMING INSTRUCTIONS
1
2
#1
3
#1
CONN 1
)
4
#2
5
#2
6
You have 60 seconds to complete the following procedure
7
.
turn
.
8
After 15 seconds
Check engine will stop flashing, turn the ignition OFF and remove the
key. If the programming fails wait 3 to 5 minutes before trying to
program again
The PATS is now programmed.
Reassemble the key.
Technical support:
TEL: 514-255-HELP (4357)
FAX: 514-255-1367
Web: www.ifar.ca
INSTALLATION GUIDE
Made in Canada - Rev. A - 17 / 12 / 2007
W e b
s i t e :
h t t p : / / w w w . i f a r . c a
CAN High: White/Orange CAN Low: White
Blue/Black
Purple/Orange
CAN High: White/Orange CAN Low: White
Purple/Orange
CAN High: White/Orange CAN Low: White
Black/Yellow
CAN High: White/Orange CAN Low: White/Pink
Purple/Orange
CAN High: White/Orange CAN Low: White
Black/White
CAN High: White/Orange CAN Low: White
Purple/Orange
CAN High: White/Orange CAN Low: White
Black/white
CAN High: White/Green CAN Low: White/Blue
CAN High: White/Orange CAN Low: White
Purple/Orange
CAN High: White/Orange CAN Low: White
Purple/Orange
CAN High: White/Orange CAN Low: White
Purple/Orange
CAN High: White/Orange CAN Low: White/Pink
Black/Yellow
CAN High: White/Orange CAN Low: White
Purple/Orange
CAN High: White/Orange CAN Low: White/Pink
Black/Yellow
CAN High: White/Violet CAN Low: White/Blue
Black
Connector 1 (Black):
Make 3 to 4 loose loops in front of the ignition
barrel.(Behind the plastic cover) (Secure the
wire with tie-wrap.)
Connector 2 (White):
Make the connections
Two (2) functional keys are required for
programming. Insert the first key into
the ignition switch and turn the
Ignition ON
Turn the key
first key.
Insert the second key and turn the
ignition ON
Turn the key
first key.
Remove back cover and internal
circuit (Circuit Board) from key-
remote (as battery replacement).
Place the
(without circuit board) against
PATS as shown on box label.
Keep both pieces together
insert this key-remote into the
ignition switch and
both
, a
chime
will sound. The
CAN
page 2
.
for
10 seconds.
OFF
and remove the
for
10 seconds
.
OFF
and remove the
empty
key-remote
and
turn them
to the
ON position
.
SECURITY
light or
P.4

Publicité

loading