Laserworld ShowNET Mode D'emploi page 7

Manual: Laserworld ShowNET - Network Interface
Change the option.
Click on ‚Store Data' to save your changes. Click on ‚OK' twice and wait until another win-
dow opens that asks to restart the ILDA interface. To do so, switch the laser system off
and on again.
(1) DJ Mode
To get laser output, DMX channel 1 needs to have a value greater than 0 (recommended
64 to 192)
Channel Mode Value
1 Intensity DJ 0
1 - 255
2 Pattern selection DJ 0
1 - 255
3 Pattern speed DJ 0 - 15
(Framerate)
16 - 255
4 Size DJ 0 - 127
128 - 191
192 - 255
5 Automatic size DJ 0 - 63
64 - 127
128 - 191
192 - 255
6 Rotate DJ 0 - 192
193 - 224
225 - 255
7 Position X-axis coarse DJ 0 - 255
8 Position X-axis fine DJ 0 - 255
9 Position Y-axis coarse DJ 0 - 255
10 Position Y-axis fine DJ 0 - 255
page 12 / 54
Function
Laser off
Increase intensity (full intensity = 255)
Blackout (000.ild must not exist)
Display patterns from SD card:
1 = 001.ild
2 = 002.ild
... and so on
If no pattern is assigned to a number = blackout
Standard speed: 50 fps
Increasing speed from 0 fps to 100 fps
Decreasing size X + Y-axis
Decreasing size X-axis
Decreasing size Y-axis
Full size
Changing size automatically X + Y-axis
(increasing speed)
Changing size automatically X-axis
(increasing speed)
Changing size automatically Y-axis
(increasing speed)
Manual rotation
Automatic rotation anti-clockwise
(increasing speed)
Automatic rotation clockwise
(increasing speed)
0 = center
0 = center
Channel Mode Value
11 Color effects DJ 0 - 15
16 - 79
80 - 143
144 - 255
12 Color effects DJ 0 - 127
extended
128 - 192
193 - 255
13 Strobe DJ 0 - 15
16 - 255
14 Operation mode DJ 0 - 19
20 - 83
84 - 147
148 - 211
212 - 233
234 - 255
15 Scan speed DJ 0 - 31
32 - 255
16 Safety zone size DJ 0 - 63
64 - 127
128 - 191
192 - 255
17 Safety zone intensity DJ 0
1 - 128
129 - 255
18 Blanking DJ 0 - 192
193 - 255
19 Blankshift DJ 0 - 192
193 - 255
Manual: Laserworld ShowNET - Network Interface
Function
Show pattern in original colors
Show pattern in different colors (monochrome)
Re-color effects:
Original colors are replaced by new colors
Automatic change of re-color effects
Smooth color fade effect to the re-color effect
Value of channel 11 must be >15!
Blocking color effect to the re-color effect
Value of channel 11 must be >15!
Automatic change of color fade effects
None
Increasing strobe effect
DMX
Automatic position X & Y-axis
Automatic position X-axis
Automatic position Y-axis
Demonstration mode
Sound-to-light
Default
Increasing scan speed (from 5 kpps to 30 kpps)
ATTENTION: If you're unsure about the maxi-
mum scan speed, stay with the default setting!
Size of horizontal safety zone
Safety zone is the bottom side
Size of horizontal safety zone
Safety zone is the upper side
Size of vertical safety zone
Safety zone is the left side
Size of the vertical safety zone
Safety zone is the right side
No reduction
Decrease brightness up to half brightness
Decrease brightness up to blackout
Manual select how much of the laser pattern
shall be blanked
Automatic blanking (increasing speed)
Manual select the pattern part the blanking of
channel 18 shall be applied to
Automatic blank shift (increasing speed)
page 13 / 54