Westin Automotive Products 32-1120 Consignes

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-1120
32-1125
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 2 U-BOLT
7 4 3/8-16 X 1.25" HEX HEAD BOLT
8 8 3/8" SAE FLAT WASHER
9 4 3/8" USS FLAT WASHER
10 8 3/8" LOCK WASHER
11 8 3/8-16 HEX NUT
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 PIEZA DE SUJECIÓN, LADO DEL ACOMPAÑANTE
4 2 TAPONES DE PLÁSTICO
5 4 PARACHOQUES DE HULE
6 2 PERNOS EN "U"
7 4 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,25"
8 8 ARANDELA PLANA SAE DE 3/8"
9 4 ARANDELA PLANA USS DE 3/8"
10 8 ARANDELAS DE PRESIÓN DE 3/8"
11 8 TUERCAS HEXAGONALES DE 3/8-16
1 1 LA BULL BAR
2,3 2 SUPPORT CÔTÉ PASSAGER (2) ET CÔTÉ CONDUCTEUR (3)
4 2 BOUCHON DE PLASTIQUE
5 4 PARE-CHOCS EN CAOUTCHOUC
6 2 BOULON EN U
7 4 BOULON A TETE HEXAGONALE 3/8-16 X 1,25 PO
8 8 RONDELLE PLATE SAE 3/8 PO
9 4 RONDELLE PLATE USS 2/8 PO
10 4 RONDELLE A FREIN 3/8 PO
11 8 ÉCROU HEXAGONAL 3/8-16
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning.
STEP 2. NOTE:
It will be necessary to remove the front license plate and bracket. Remove license plate from bracket. Using a
3/16" drill bit, drill out the two pop rivets that hold the bracket to the bumper. If local/state laws requires a license plate,
license plate relocation kit 32-0055 is available.
VEHICLES WITH TOW HOOKS
STEP 3.
Remove tow hooks by removing front and rear bolts.
frame stays aligned with holes.
STEP 4.
Position bottom bracket up to bottom of frame and replace tow hook bolts.
VEHICLES WITHOUT TOW HOOKS
STEP 5.
Insert u-bolt in frame as shown.
SEE FIGURE 4.
STEP 6.
Attach Bull Bar to mount brackets using 3/8" fasteners. Make sure Bull Bar and brackets are properly aligned and tighten
all fasteners. Recommended torque values are 20 Ft.Lbs. for 3/8" fasteners.
LIGHT INSTALLATION:
socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube. Thread nut and
washers on stud and tighten.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2003-06 FORD EXPEDITION/LINCOLN NAVIGATOR 2/4 WHEEL
APLICACIÓN: FORD EXPEDITION/LINCOLN NAVIGATOR TRACCIÓN 2/4, MOD.
APPLICATION: FORD EXPEDITION/LINCOLN NAVIGATOR 2 OU 4 ROUES
CONTENTS - CONTENIDO
SEE FIGURES 3 AND 4.
Hand Tighten.
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension and
SEE FIGURE 1. NOTE:
DRIVE
2003-06
MOTRICES 2003-06
- CONTENU
(2) Y EL CONDUCTOR
NOTE:
Tow hooks will not be reinstalled. Make sure nut plate in
Attach bracket to u-bolts using 3/8" fasteners as shown.
A short socket, not a deep well works best to get the nut
2
TOOLS - HERRAMIENTA
9/16" SOCKET
9/16" WRENCH
15MM SOCKET
RATCHET
SOCKET EXTENSION
TORQUE WRENCH
DADO DE 9/16 "
(3) LLAVE DE TUERCAS DE 9/16"
DADO DE 15 MM
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
DADO DE 9/16 PO
CLE 9/16 PO
DADO DE 15MM
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
SEE FIGURE 2.
Go to step 6.
WO: 206824
75-0419 REVISION A 2/14/07
3
6
- OUTILS