Publicité
Les langues disponibles
Les langues disponibles
FIGURE
5
-
RECTANGULAR SHOWER BASE - WITH BUILT IN 1''
TILE FLANGE ON 3 SIDES
TOP VIEW
A
C
Series of Strada Bases with built in 1'' Tile Flange on 3 sides
listed in the Table 2.
SB 4 42
2
SB 4236
SB 3634
Inch
mm
Inch mm
Inch
4
2
1
067
42 1067
36 914
A
42 1067
36 914
34 864
B
21
533
21 533
18 457
C
18 457
17
D
21
533
E
3
76
3
76
3
Position and level the shower base. Fasten the flange of the base to the wall studs
with 5/8" (16mm) or longer screws.
flange before fastening. Finish the wall as shown in Figure 6
FIGURE 6 - WALL FINISHING
TILE FLANGE
FIGURE 7 - FLANGE SCREWS LOCATION
3 Sided Alcove Flange,
W open
60 Shorncliffe Rd., Toronto, Ontario M8Z 5K1
Telephone: (416) 231-9030 - Fax: (416) 231-0929
FRONT VIEW
SIDE VIEW
STUD
102 mm
3/8" 10 mm
SB 3632
SB 6042
mm
Inch
mm
Inch mm
60 1524
36
914
42 1067
32
813
30
762
18
457
432
21
533
16
406
3
76
76
3
76
Note:
Remove the protective film from the tile
2 x 4
"
''
WALL STUD
SCREW
Left Back Wall Flange
,
Right, Back Wall Flange
We want you to be completely satisfied with our products and service. If you have any comments or suggestions, please call
The company reserves the right to change models and specifications without notice.
www.mirolin.com
TESTING
Test the installation after completing the plumbing, but
before enclosing the ba
surroundings.
1"
F
25 mm
ensure that the adjustment of the drain-overflow
assembly is correct, and that there are no leaks.
Mirolin Industries Corp. will not be liable for any kind of
3"
4"
damages as a result of not water testing the unit prior to
76 mm
use by end user.
FINISHING
!
!
Mirolin Industries Corp. is not responsible for any
SB 6030
SB 6032
Inch
mm
mm
Inch
INSTALLATION CLEAN-UP
60
1
524
60
1
524
Remove construction dirt and residue with a mild liquid
30
762
32
813
detergent. DO NOT USE abrasive cleaners, scouring
compounds and pads, metal scrapers, steel wool, or
30
762
30
762
other materials that could damage or dull the surface of
15
381
16
406
the bath.
3
76
3
76
Remove plaster carefully with a blunt wooden block
having rounded edges.
Remove paint and other stubborn stains with isopropyl
(rubbing) alcohol.
DO NOT USE products such as acetone (nail polish
.
remover), dry cleaning solution, lacquer thinners,
gasoline, pine oil, etc.
MAINTENANCE
The acrylic sheet, which forms the surface of your
DRYWALL
bathtub, provides one of the most durable surfaces
TILE
found in modern bathrooms. Keep it bright and smooth
with mild liquid household detergent, soap and water,
SILICONE
CAULKING
or foaming cleansers. NEVER USE aromatic solvents,
abrasive cleaners, scouring compounds or pads,
strong liquid cleansers, or other material that could
damage or dull the surface of the bath.
Restoring Surface Gloss.- Restore surface gloss by
applying a very fine rubbing compound and polishing
DRAIN
the surface by hand or with a power buffer. Finish with
an application of a good quality automotive wax.
Minor Repairs to Surface.- Remove minor scratches
and scuffs as follows. First, wet sand the area with 600
grit wet sandpaper until the surface is smooth. Then,
restore the gloss as described under RESTORING
SURFACE GLOSS.
1-800-MIROLIN toll free.
Customer Service: (416) 231-5790
Canada, U.S.A.: 1-800 -
Fax, Canada: 1- 800 - 463 - 2236
ill the ba
se
with water and leave it for one hour to
Apply trim around the shower base periphery to
finish drywall, if required.
Install Shower Door according to the
manufacturer's instructions if purchased
damages incurred as a result of poor installation of
the product.
MIROLIN
(647-6546)
se
and finishing the
84 214
18
Jan
. 201
7
2
Publicité
