Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

OPERATING THE UIIT

1.- RESET BUTTON

The unit must be reset under the following conditions:
A) Prior to using this unit for the first time after installation.
B) If the unit fails to operate properly, press the RESET with a pen tip or other pointed instrument.
2. - SEL & VOL CONTROL BUTTON
A) Press the SEL repeatedly to select VOLUME - BASS - TREBLE - BALANCE - FADER.
B)Press SEL button and hold for more than 2 seconds to turn on TA ON/OFF mode, then press SEL button shortly and
repeatedly
to select AF ON/OFF,TA SEEK/TA ALARM PI SOUND/PI MUTE, RETUNE L/RETUNE S, MASKDPI/MASK ALL,
BEEP ON/BEEP OFF, USER SET(FLAT/CLASSIC/ROCK/POP),VOL LAST/VOL DEFA , STEREO/MONO(in FM mode),
LOUD OFF/LOUD ON,DX/LOCAL (in FM mode), CLK ON/CLK OFF,CLK 12/24 mode.
After selecting the desired mode, rotate the VOL- or VOL+ button to select one setup item of the desired mode.
1) TA SEEK/TA ALARM:
TA SEEK mode: when newly tuned station does not receive TP information for 5seconds,the radio retunes to next
station which has adifferent PI to the last station,but has the TPinformation. When TP information gets lost at the current
station for retune time which is set byRETUNE SHORT(90 seconds) or RETUNE LONG(150seconds), the radio starts
to retune to next same PIstation. When same PI station does not receive in 1cyclic search,the radio retunes to next
station with TP information.
TA ALARM mode: when this mode is selected, any autoretune mode is not activated. Only double beep sound (ALARM)
will be heard.When newly tuned station does not have TP information for 5 seconds, beeps are sounded.
When TP information gets lost at the current station for retune time, the beep sound will be heard.When newly tuned
station has no RDS signal, PI SEEK is suppressed .
2) PI SOUND/ PI MUTE:
PI SOUND mode: if a car cruises between buildings that could cause reflectinsignals, a phenomenon may occur, dueto
different PI codes being received from the sameAF source. when different PI sounds (DIP) are heard occassionally, this
will happen for less than 1 second.PI MUTE mode: under above same situation, a mute sound will be heard for less
than1second.
3) RETUNE L / RETUNE S:
The initial time of auto TA search or PI SEARCH mode is selected. When PI information is not received forretune
interval , the radio starts to retune to next same PI station.When same PI station does not receive 1 cyclic search, the
radio goes to last stationand waits for 4-5 minutes until PI code is received.
RETUNE L mode: selected as 150 seconds.
RETUNE S mode: selected as 90 seconds.
4) MASK DPI/MASK ALL:
MASK DPI mode: masks only the AF which has different PI.
MASK ALL mode: masks the AF which has different PI and NO RDS signal with high field strength.
5)BEEP ON/BEEP OFF
BEEP ON mode: The beep is generated when any key is pressed.
BEEP OFF mode: The beep sound is disabled.
6) VOL LAST/VOL DEFA
VOL LAST: The radio switches on at the actual volume it had when it was last switched off.
VOL DEFA: After pressing SEL button, AVOL will be displayed. Then you can pre-select a constant switch-on volume by
using the VOL knob.
7)CLK ON/OFF
CLK ON: Clock will always show on the display when power off.
CLK OFF: Clock will disappear on the display when power off.
3. -POWER ON/OFF AND MUTE
Press the POWER to turn on this unit. To turn off theunit, press and hold this button unit it off.
During playing, press this to mute the sound.
4. - LCD DISPLAY
All manuals and user guides at all-guides.com
1

Publicité

Table des Matières
loading

Table des Matières