Hubbell Prescolite CFR6EB Instructions D'installation

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions concerning
Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in areas subject
to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off power at fuse or circuit breaker.
All servicing or relamping must be performed by qualified service personnel. Product must be grounded to avoid
potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a
manner consistent with its intended use, and in compliance with the National Electrical Code and local codes. The use
of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block
light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
INSTALLATION INSTRUCTIONS
IMPORTANT: FOR WALL WASH UNITS ONLY-FIXTURE MUST BE INSTALLED WITH J-BOX CLOSEST TO THE WALL TO BE ILLUMINATED.
1.
Bend brackets as shown in Detail "A". Install the
fixture in the ceiling using mounting channel or
bar (by others) placed in the adjustable mounting
brackets. Mount the fixture in the ceiling so that the
weight of the fixture is supported by the mounting
channel or bar and/or hanger wires secured to the
building structure.
2.
Adjust the fixture so the bottom of the plaster
flange is flush with the finished ceiling line and in
alignment with adjacent fixtures. Secure mounting
brackets by tightening wing nuts on either side of
the fixture.
3.
Remove J-Box cover plate. Remove appropriate
knockout and assemble appropriate connector for
the supply wire used. Connect ground wires to
green ground leads. Connect white (common) to
white (leads). Connect power supply (line) to black
lead(s). Reinstall J-Box cover.
WARNING: DO NOT pinch wires
between J-Box/ballast cover and J-Box.
Consult a Qualified Electrician for all
other options that require other wiring
configurations.
4. Connect the Mate-N-Lock Connectors
from the ballast to the connectors from
the fixture. Push all connectors and splices into
the J-Box.
5.
Install the ballast assembly by positioning the tab
on the ballast mounting plate in the slot on the
J-Box bottom plate. Secure ballast assembly by
snapping plate under J-Box Spring and bending
spring down (See Detail "B"). WARNING: Do
Not pinch Wires between Ballast and
J-Box or between J-Box and covers!
6.
After all ceiling installation and finishing work is
complete. Install the reflector.
7.
Install the proper lamps (by others).
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER OPERATION OF THE FIXTURE
DEPEND ON THE INTEGRITY OF THE WIRING.
701 Millennium Blvd., • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2018, 6/21/18 revision, All Rights Reserved - Printed in U.S.A.
CAT. NO. CFR6EB
Bend Brackets in
Line with Marks on
Flange
Press Spring
Down on
Both Sides of
the J-Box
DETAIL B
Reflector
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .05935800
Wing Nut
Dimming Control Leads
where applicable
DETAIL "A"
Page 1 of 2
For Wall Wash Units:
This Side Closest to Wall
to be illuminated
Ballast Assembly
Tab
Mate-N-Lock
Connectors
where applicable
J-Box
When Wall
Wash Trim is
used, This End
of fixture must
be positioned
towards the
Adjustable
wall.
Mounting
Bracket
NOTE: Brackets are
supplied flat. To insure
proper alignment, bend
brackets in line with
marks on flange as
shown in detail "A".