Operating Conditions - Eaton 650 Mode D'emploi

Operating conditions

◗
This product is an Uninterruptible
Power Supply (UPS) for computers
and their peripherals, television sets,
stereo systems and video recorders...
It must not be used to supply other
electrical equipment (lighting, heating,
household appliances, etc.).
UPS connections
◗ Connect the UPS 1 to the AC-
power system via a wall outlet with an
earth connector (see figure A).
◗
Plug critical equipment (computer,
monitor, modem, etc.) into the outlets
8 providing battery backup power
and surge protection (see figure B),
taking care not to exceed the rated
current indicated in amperes.
◗
Other devices (printer, scanner, fax,
etc.) can be connect to the filtered
outlets 7 that provide surge
protection (see figure B). The filtered
outlets are not backed up by battery
power in the event of a power outage.
◗
Optional fax/modem connection:
A telephone, fax, modem or Ethernet
data line can be protected against
surges by connecting it to the
telephone outlet via the UPS. The
device cable is used between the
telephone outlet and the UPS, and the
supplied cable 2 is used between
the UPS and the device, as indicated
in figure C.
◗
Optional COM connection:
The 650 and 800 VA devices can be
connected to the computer using the
special USB cable 5 supplied.
The software available on the CD-
ROM 6 (or downloadable from the
eaton.com site) can be configured to
monitor the UPS and the supply of
power to the computer (see figures D
and F).
◗
Follow the indicated procedure.
Operation
7 : Four filtered outlets.
8 : Four battery backup outlets.
9 : LED ON indicate that surge
protection is active on all eight
outlets.
10 : LED ON indicate a UPS fault.
11 : ON/OFF button for the battery
backup outlets.
12 : Protection circuit breaker.
4
8 10 11
◗
Battery charge: The UPS charges
the battery as soon as it is connected
to the AC outlet, whether button 11 is
pressed or not. When used for the first
time, the battery will only provide its
maximum autonomy after it has been
charged for 8 hours. It is
recommended that the UPS be
permanently connected to the AC
power supply to ensure the best
possible autonomy.
Filtered outlets 7 without battery
◗
backup: Equipment connected to
these outlets is supplied as soon as
the AC cord is plugged in. They are
not affected by button 11 .
◗ Battery backup outlets 8 :
Equipment connected to these outlets
is supplied as soon as button 11 is
pressed and turns green (see figure
E). These outlets can be turned on
even if the UPS is not connected to
AC power (button 11 flashes).
◗
AC-power disturbance: If AC
power is disturbed or fails, the UPS
continues to operate on battery power.
Button 11 flashes green. In normal
mode, the audio alarm beeps every 5
seconds, then every 2 seconds when
the end of battery backup time is near.
In silent mode (see the section on
customizing), the audio alarm simply
beeps once when the UPS transfers
to battery power.
◗
If the power outage lasts longer than
the battery backup time, the UPS
shuts down and automatically restarts
when power is restored. Following a
complete discharge, a few hours are
required to recharge the battery back
to full backup time.
◗
To save battery power, it is possible
9 7
to press button 11 to cut the supply of
power to the devices connected to the
battery backup outlets.
◗
Surge protection: All outlets,
whether backed up or simply filtered,
include surge protection, whatever the
position of button 11 .
◗
Shutdown of the battery backup
outlets 8 : Press button 11 for more
than two seconds.
Master and EcoControl
outlets operating procedure:
12
In order to limit energy consumption of
peripherals (scanner, printer) in
standby mode, the Protection
Station is equipped with EcoControl
outlets that are dependent on the
Master (see figure B) outlet. When
the main application supplied by the
Master outlet (computer) is shut
down, the EcoControl outlets are
automatically deactivated and the
peripherals shut down.
This function (deactivated by default)
is validated and configured using the
configuration tool integrated in the
Solution-Pac (software supplied with
your Protection Station).
Note: When the function is activated,
do not connect critical applications to
EcoControl outlets.
Threshold setup:
A default setup ensures the correct
operation of the EcoControl function.
However, depending on the
consumption of the main load, the
trigger threshold of the EcoControl
function may have to be modified
using the configuration software
supplied with the UPS:
◗
First, make sure that the function is
activated in the "EcoControl
Function" tab of the configuration
tool.
◗
If the peripherals connected to the
EcoControl outlets do not switch off
when the main load is not in normal
operation (ex: when in standby mode),
the detection threshold value must be
set to High.
◗
If the rated consumption level of the
main load is low and the EcoControl
outlets shut down when the main load
is operating normally, the detection
threshold value must be set to Low.
MAU-00075 AB