Spectro-UV Spectroline uVision Serie Mode D'emploi page 2

UV emitted from this product. Avoid eye and skin exposure to unshielded products.
FOR PROFESSIONAL EXAMINATION USE ONLY
IMPORTANT SAFETY INSTRUCTIONS (Read all instructions)
• Do not operate the uVision™ Series UV-A/White Light LED NDT Inspection Lamp
(UV-365SBLCR) if the lamp has been damaged.
Do not look directly into the light. ALWAYS wear the UV-absorbing protective glasses
•
provided when operating the lamp. Use in low-light conditions to achieve the best
inspection results. The darker the room, the greater the fluorescent contrast.
• The uVision™ is not approved for use in hazardous atmospheres. Do not attempt to use
it in areas requiring explosion-proof lighting.
• Never use this equipment in any manner not specified in these instructions because
your protection may be impaired.
• NEVER aim the lamp in the direction of another human being. It is meant for
professional fluorescent inspections ONLY!
• DO NOT attempt to modify the lens assembly or light output. Doing so may alter the
performance and intensity of the uVision™.
OPERATION
• The uVision™ series UV-A inspection lamps are equipped with a 50 ft. (15.3 m) heavy-
duty power cord and retractable reel.
• The lamp is shipped with the correct cord installed for the country of destination.
• Connect the plug to a power source that complies with the electrical requirements
specified on the label.
• The lamp has a three-position rocker power switch (II – UV; O – off; I – white light) on
the handle.
• The UV-365SBLCR has a White Light Intensity Adjustment Control located on the back
plate of the lamp. The Power Indicator is also located on the back plate of the lamp.
The Power Indicator light will be Orange when the lamp is operating within RRES
compliance.
• The UV-365SBLCR is designed to automatically shut off if the unit operates outside of
RRES compliance standards. To turn the unit back ON from a shut off event, turn the
lamp OFF and then ON using the three-position rocker switch.
• WARNING: Be sure to use genuine uVision™ replacement parts. Using another
manufacturer's replacement parts could affect product performance and will void the
warranty.
Rocker Switch
SUPPLY
CHANGING THE LAMP POWER
The appropriate cord for the country of destination will be installed on the lamp when it is
ordered. The power cord is integrated into the lower portion of the lamp handle, forming a
cord/handle assembly. A set of detailed instructions for changing the lamp cord come with
the replacement parts. Contact Customer Service for more details. Call toll-free 1-866-230-
7305.
WARNING
White Light
Intensity
Adjustment
2
DISASSEMBLING THE FILTER PROTECTOR FOR MAINTENACE
The outer rubber cover/filter holder may be removed periodically to clean the Borofloat
glass filter. To disassemble the Borofloat
rubber cover/filter holder. Peel the rubber cover/filter holder toward the front portion of the
lamp.
The Borofloat glass filter will remain inside the protector. To remove the Borofloat
®
filter, peel around the edge of the rubber cover/filter holder and push the glass filter out.
To replace or reinsert the Borofloat
Borofloat glass filter into the channel of the rubber cover/filter holder. Manipulate the rubber
®
cover around the filter. Ensure the glass filter is evenly seated.
REPLACING THE UV LENSES
The UV-A lenses (UL-110) covering the three UV-A LEDs must be replaced over time. They
will solarize (become cloudy and yellow) from repeated use. A set of detailed instructions
come with the replacement UV-A lenses (UL-110). See Replacement Parts section and
contact Customer Service for more details.
Orange = Power on, battery good
Blink Orange and Red = Low Battery; time left approx. 10 – 15 mins
Red = Dead Battery, Approx. 5 minutes or less remaining
Shut Down
ENVIRONMENTAL SPECIFICATIONS
The UV-365SBLCR lamp is designed to be safe under the following conditions:
Power
• For Indoor/Outdoor Use (dustproof and protected against jets of water);
Indicator
• Temperature 41°F to 122°F (5°C to 50°C);
• Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage.
LIMITED WARRANTY
The warranty policy for the uVision™ lamp is provided on the Certificate of Limited Warranty
enclosed separately with each unit. NOTE: For assistance of any kind, please contact the
Customer Service Department at Spectro-UV. Provide the model, the serial number of the
unit, and the date of purchase. The unit's serialization information is located (1) on the
packaging the unit is shipped in, (2) engraved on the unit's handle, and (3) labeled on the
reverse side of the unit's back plate.
Filter Protector (FP-600), first remove the front
®
glass filter into the rubber cover/filter holder, slide the
®
BATTERY LED INDICATOR STATUS
3
®
glass
®