Publicité
Liens rapides
Model/Modelo/Modèle
564-MPU-DST
Series/Series/Seria
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
For easy installation of your Delta
faucet you will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and maintenance
information.
Para instalación fácil de su llave Delta
usted necesitará:
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
Pour installer votre robinet Delta
facilement, vous devez:
• LIRE TOUTES les instructions avant de débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
www.deltafaucet.com
77253
SINGLE HANDLE LAVATORY
CENTERSET AND VESSEL FAUCETS
LLAVES MONOCONTROL DE MONTURA
DE CENTRO PARA LAVAMANOS
ROBINETS À ENTRAXE COURT À
UNE POIGNÉE
You may need/Usted puede necesitar/
Articles dont vous pouvez avoir besoin:
1/8"
1
T E FLO N
1/8"
6/30/15
Rev. D
Publicité
Manuels Connexes pour Delta 564-MPU-DST Serie
Sommaire des Matières pour Delta 564-MPU-DST Serie
- Page 1 • To READ ALL warnings, care, and maintenance information. 1/8" 1/8" Para instalación fácil de su llave Delta usted necesitará: • LEER TODAS las instrucciones completamente antes de empezar. • LEER TODOS los avisos, cuidados, e información de mantenimiento.
- Page 2 Si la reparación o su reemplazo no es práctico, Delta Faucet Company tiene DELTA FAUCET COMPANY NO SE HACE RESPONSABLE POR CUALQUIER DAÑO ESPECIAL, la opción de reembolsarle su dinero por la cantidad del precio de compra a cambio de la devolución...
- Page 3 For Three Hole Installation: For Single Hole Installation: Slide escutcheon (1) and spacer with round gasket (2) up over Slide single hole escutcheon (1) and spacer with round gasket tubes and mounting stud. Position spacer and gasket under (2) up over tubes and mounting stud. Slide tubes down through escutcheon.
- Page 4 Side View Vista lateral Vue latérale Secure outlet fitting (1) to spout line (2) using clip (3). Install as shown. Fije el accesorio de salida (1) al tubo del surtidor(2) utilizando el gancho (3). Instale como se muestra. Fixez le raccord de sortie (1) au tube du bec (2) à l’aide de l’agrafe (3). Effectuez l’installation de la manière indiquée sur la figure. 77253 Rev.
- Page 5 Faucet fittings (1) are 3/8" compression, with allows a leak-free joint to be created. Delta is not being careful not to cut the tube too short. ends colored red for hot and blue for cold. Loop...
- Page 6 Incorrect Installation Correct method Instalación Incorrecta Método Correcto Installation Incorrecte Bonne méthode Do not install sleeve Ensure cut is straight. upside down. Custom Fit Connections - Plastic Sleeve Installation Instructions No instale la manga Asegúrese que el boca abajo. corte esté recto. 1.
- Page 7 Step 3b Metal Pop-Up Remove stopper (1) and flange (2). Apply silicone to underside of flange (1). Insert Remove pivot nut (1). Install horizontal Step 3c body (2) into sink. Screw flange (1) into body (2). rod (2) and stopper (3) as removable Screw nut (1) all the way down.
- Page 8 Remove aerator (1) using supplied wrench (2) and move faucet Check all connections at arrows for leaks. Retighten if necessary, handle (3) to the full on mixed position. Turn on hot and cold water but do not overtighten. supplies (4) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts.
- Page 9 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two this handle limit stop will not always prevent scalding because it positions. Position 1, to the left, allows full handle motion (the full range does not compensate for incoming pressure or sudden water between “all cold”...
- Page 10 For Installations That Do Not Require A Lift Rod Insert button (1) into hole on back of spout (2). Para instalaciones que no requieren una barrita para abrir el desagüe Inserte el botón (1) en el agujero en la parte posterior del surtidor (2). Pour les installations qui n’exigent pas de tirette Introduisez le bouton (1) dans le trou à...
-
Page 11: Entretien
1/8" Maintenance Cleaning and Care If faucet exhibits very low flow: Care should be given to the cleaning of this reinstalling parts, make sure bonnet nut (4) is A. Remove and clean aerator (1) with supplied tightened securely with a wrench.* product. - Page 12 Model / Modelo / Modèle 564-MPU-DST RP54974 Button / Botón / Bouton RP77264▲ RP40650 Handle, Button & Set Screw Set Screw Manija, Botón l y Tornillo de Ajuste Tornillo de Ajuste ▲Specify Finish Manette, Bouton et Vis de Calage Vis de calage Especifíque el Acabado Précisez le Fini RP54972▲...