Safety Advice; Maintenance Instructions - Puris Kera trends Serie Instructions De Montage

SAFETY ADVICE

• The mounting must only be done by experts.
• Warning: defective mounting is dangerous!
• Check whether the wall is suitable for the mounting and
that the fasteners are strong enough for the forces involved.
• Please read through the mounting instructions carefully
before mounting in the bathroom.
• The enclosed fastening material is only suitable for solid
walls of sufficient load-bearing strength.
• Electrical installations should only be carried out by a
specialist electrician DIN VDE 0100-701 (VDE 0100-701):2008-10.
• Electrified, mirrored cabinets and flat mirrors must be located at
a minimum distance of 600 mm away from the bath or shower.
• The safety regulations and standards of the particular coun-
tries must be observed.
IMPORTANT INFORMATION
• Inspect the packaging for external damage when it is delivered.
• Please check the number of bathroom cabinets supplied and
the associated sets of ironmongery (screws, cover caps,
handles, etc.) against the delivery note or the articleʼs label
on the packaging.
• Caution: only remove the protective caps on the mirrored
cabinetʼs doors after mounting the doors, in order to avoid
damaging edges of the mirrors.
• Use suitable spacers or distance blocks to even out the
existing differences in level caused by coverings applied to
the walls, e.g., partial tiling.
• Reinforce any walls of insufficient load-bearing strength.
• The drilled dimensions are measured from the FFL according
to the dimensioned layout.
• Fasten the cabinets with the suspension rails:
- Washstand base cabinet
- Tall cupboard (with 600 mm width)
• Always fasten the hanging bar to the wall with 2 screws!
• The horizontal spacing between the cabinets can be chosen freely.
• Do not tighten water tap and sink pop-up too firmly.
• Bonding between washstand and shelf with silicone
(transparent and solvent-free).
• Handle glass washstand with care!
TOOLS
• Jigsaw
• Drill and battery-operated screwdriver
• Stone drill bit of 8 mm and 14 mm dia.
• Wood drill bit of 4 mm and 10 mm dia.
• Folding metre rule and measuring tape
• Spirit level
• Screwdriver with a 3.5 mm tip for Phillips screws
• 4 mm Allen key
• 8 mm, 10 mm and 17 mm wide open-jawed spanner
• Screw clamps
• Pencil
• Silicone sealant (transparent and solvent-free)
KEEP THE INSTRUCTIONS IN A SAFE PLACE
i
Caution: keep the instructions safely because they contain
information about installing and operating the products.

MAINTENANCE INSTRUCTIONS

• Caution: do not use any chemicals, aggressive detergent
paste or scouring powder.
• The best way of cleaning the cabinet is to use a damp cloth
with some mild washing-up liquid.
• Take care that no residue from droplets remains on the lower
edge of bathroom cabinets.
• Polish the mirror with a damp cloth or chamois leather.
• The washbasin can be easily cleaned with any of the usual,
non-abrasive cleaning agents.
MOUNTING SEQUENCE
i
Illustrations in the appendix
1. Remove doors and drawers (Fig. A/A1)
2. Mounting the lights (Figs. B/B1/B2/B3)
The electrical mains supply cable must be voltage-free!
3. Suspending the cabinets
· Mirrored cabinet or flat mirror
(centre of the mirrored cabinet =
centre of the water supply connection)
· Upper cabinets, centre cabinets, tall cabinets
· Plug-in board
· High board
· Washstand base cabinet/Washstand
(centre of the washstand base cabinet =
centre of the water supply connection)
4. Aligning the flat mirror (Fig. C)
5. Aligning the cabinets (Fig. D)
6. Mount fitting board (Fig. E)
7. Mount washstand
For ceramic washstand:
· Put washstand in place, align, mount (Fig. F)
· Seal washstand (Fig. F1)
For glass washbasin:
· Drilling of clearance hole (Fig. G)
· Sawing of cut-out for washstand (Fig. G1)
· Attaching shelf for washstand (Fig. G2)
· Mounting of shelf (Fig. G3)
· Glue washstand with shelf (Fig. G4)
· Tightly press together washstand with shelf (Fig. G5)
· Sealing the washstand (Figs. G6/G7)
For top-fitted washstand:
· Sawing of cut-out for washstand (Fig. H)
· Attaching shelf for washstand (Fig. H1)
· Mounting of shelf (Fig. H2)
· Mount the cabinet and align
· Align the washstand and mark
· Remove the washstand and cabinet
· Mount the washstand (Fig. H3)
· Mount the cabinet
· Seal the washstand and cabinet (Fig. H4)
8. Affixing of the fitting (Fig. I)
· Caution: Use attached rubber seal.
· Do not tighten fitting too firmly!
9. Screwing on the shelf (Fig. J)
· Caution: do not drill through the shelf!
· Use the screws supplied.
10. Mount doors and drawers (Fig. K/K1)
11. Adjustment of door damping (Fig. L)
12. Aligning the doors (Figs. M/M1/M2)
13. Glue handles onto the door of the mirrored cabinet (Fig. N)
14. Adjusting the folding hinge (Fig. O)
15. Adjusting the drawer (Figs. P/P1)
CHANGING THE FLOURESCENT TUBE
i
Figures: page 29 (Q)
The electrical mains supply cable must be voltage-free!
3