Table des Matières
Publicité
Options de configuration de fonctionnement électrique.
Système carte circuit imprimé Rev. B
J50
J52
J
J51
F6, T30A 480V
J25 5
J32 2
TB1
1
2
L1
3
L2
4
J57
Balboa
HTR2
W1
BALBOA INSTRUMENTS, INC.
GS500Z
Pb b P P P P
COPYRIGHT 2007
MADE IN U.S.A.
P/N 22015_B
J50
J52
J
J51
F6, T30A 480V
J25 5
J32 2
TB1
1
2
L1
3
L2
4
J57
Balboa
HTR2
W1
BALBOA INSTRUMENTS, INC.
GS500Z
Pb b P P
COPYRIGHT 2007
MADE IN U.S.A.
P/N 22015_B
L3
Line 3 - Cap (Insulate) end,
Do not connect.
NOTE:
AV
J29
J23
OZONE
PUMP 1
G
N
CIRC. PUMP
G
N
F4, T0.2A 250V
J58
J58
W2
J28
J28 8
K2
J101
00
HTR1
AV
J23
J29
OZONE
PUMP 1
G
N
CIRC. PUMP
G
N
F4, T0.2A 250V
J58
J58
W2
J28
J28 8
K2
J101
00
HTR1
K1
K6
K9
Fonctionnement simple, systèmes électrique IT (Pas de Neutre)
J46
J46
Single Service, IT Electrical System (No Neutral)
Ligne – Tension de la ligne est 230VAC (1 x 16 Amp or 1 x 32
K8
Line - Line voltage is 230VAC (1 x 16 Amp or 1 x 32 Amp)
Amp). 3 conducteurs (2 phases + 1 prise de terre)
3 Wires (2 Lines + 1 Protective Earth)
10VAC
J17/26
J72
Le conducteur de prise de terre (vert/jaune) doit être connecté à la
OPT. BLWR/PUMP 2
T1
Protective Earth wire (Green/Yellow) must be connected
masse du système comme indiqué.
to system ground terminal as marked.
J1
All equipment (pumps, blower, and heater) runs on
J2
service line L1 with L2 acting as the return.
Systems using only 1 DIP switch (A10) for heat disable:
J10
J43
seulement 1 commutateur DIP (A10):
For 1 x 16 Amp Service:
F2
S1
J90
DIP Switch A10 must be ON.
en position ON.
J60
J6
1
For 1 x 32 Amp Service:
TST
SWITCHBANK A
EXT RLY
AUX F
Set DIP Switch A10 such that total system amperage
draw never exceeds rated service input.
Systems using multiple DIP switches for heat disable:
Refer to system Hot Sheet DIP Switch Definition page
plusieurs commutateurs DIP:
and set the switches shown in Table 1 such that total
system amperage draw never exceeds rated service input.
K1
K6
K9
J46
J46
Fonctionnement triphasé, systèmes électrique IT (Pas de Neutre)
3-Phase Service, IT Electrical System (No Neutral)
K8
Ligne – Tension de la ligne est 230VAC
Line - Line voltage is 230VAC
4 conducteurs (3 phases + 1 prise de terre)
4 Wires (3 Lines + 1 Protective Earth)
10VAC
J17/26
J72
OPT. BLWR/PUMP 2
T1
Le conducteur de prise de terre (vert/jaune) doit être connecté à la masse du
Protective Earth wire (Green/Yellow) must be connected
système comme indiqué.
to system ground terminal as marked.
J1
Tous équipements (pompes, blower, et réchauffeur) utilisent la ligne L1 avec la
All equipment (pumps, blower, and heater) runs on
J2
ligne L2 servant comme le retour.
service line L1 with L2 acting as the return.
Systems using only 1 DIP switch (A10) for heat disable:
J10
J43
For 1 x 16 Amp Service:
F2
S1
J90
DIP Switch A10 must be ON.
J60
J6
1
For 1 x 32 Amp Service:
TST
SWITCHBANK A
EXT RLY
AUX F
Set DIP Switch A10 such that total system amperage
draw never exceeds rated service input.
Systems using multiple DIP switches for heat disable:
commutateurs DIP:
Refer to system Hot Sheet DIP Switch Definition page
and set the switches shown in Table 1 such that total
system amperage draw never exceeds rated service input.
Page 10
F1
F7
J13
F10A 250V
F3A 250V
K5
J20
C9
G
N
F3
J71
1
J18
U4
J19
J12
J8
J44
J7
1
1
1
1
1
J11
SEN A
SEN B
VAC
F1
F7
J13
F10A 250V
F3A 250V
K5
J20
C9
G
N
F3
J71
1
J18
U4
J19
J12
J7
J8
J44
1
1
1
1
1
J11
SEN A
SEN B
VAC
55250_97_B
Publicité
Table des Matières
