Tools Required - Legacy Levelwind L8305 Manuel D'instructions

SEVEN POSITION LOCKING BRACE
LEVELWIND retractable hose reels can swing freely on bracket
or can be locked in one of seven positions, allowing for specific
mounting requirements.
Standard bracket
1) Remove bracket rod from reel (SEE FIG. 5A).
2) Place seven position locking brace over bracket so
that bracket rod holes are aligned. Replace bracket rod so that
brace, reel & bracket are attached. Insert hitch-pin clip through
end of bracket rod (SEE FIG. 5B).
3) Rotate bracket so that it is at desired angle & lock
into place with fastener (SEE FIG. 5B).
Maintenance Procedures
TENSION ADJUSTMENT:
This reel is preloaded with spring tension that is set at the factory.
If the reel becomes completely untensioned, please identify
your hose reel model number referenced in the Factory Preset
Tensioning Table to find out how many turns are needed for proper
tensioning. If a heavy air tool is attached to the end of the hose,
you may need to add tension to overcome the weight of this tool.
DO NOT EXCEED one full turn past the number of turns listed in
the Factory Preset Tensioning Chart below.

TOOLS REQUIRED:

Phillips Screw Driver, 3/4 in. Socket Wrench
1) Lay reel on its side (SEE FIG. 7).
2) Place wrench on hub fitting plate nut. HOLD WRENCH
FIRMLY.
3) Unscrew hub. DO NOT REMOVE SIDEPLATE.
4) Turn wrench either ½ turn or no more than one full turn.
Turn clockwise to increase tension. Turn counterclockwise
to decrease tension.
5) Replace hub plate screws and tighten. Return reel to
mounting bracket.
HOSE REPLACEMENT:
To ensure proper performance, please consult the Hose
Replacement Kit table for the appropriate part number
to order. Call 1(800) 645-8258 to order kit.
Replacement Hose Kits
1) Pull entire length of hose out of reel (SEE FIG. 8).
2) While entire length of hose is out of the reel, place long
screw driver (3/8 in. in diameter (9 mm)) all the way
though the hole located at the back portion of reel. This
eliminates any chance for the reel to retract while replac-
ing hose.
Sideplate removal
3) Locate inlet sideplate. Remove four f
grooves located on the top and bottom of sideplate, depress locking tabs at the same
time with thumbs (SEE FIG. 10). Rotate side plate either way until sideplate unlocks.
Remove sideplate.
4) Remove wear plate (SEE FIG. 11).
wear ring (SEE FIG. 12).
While placing fingers
asteners (SEE FIG. 9). While placing fingers on
Unscrew two fasteners on wear ring and remove
Factory Preset Tensioning Table
Levelwind
TM
L8305 / L8305FZ
L8306 / L8306FZ / L8306-EU
L8340FZ
L8310 / L8310-EU
L8335 / L8335FZ / L8335-EU
L8344 / L8345 / L8346 /
L8349
L8350
Replacement Hose Kits
Model # Description
RP005005 Replacement Hose Assembly for L8305
RP005005-FZ Replacement Hose Assembly for L8305FZ
RP005006 Replacement Hose Assembly for L8306
RP005006-EU Replacement Hose Assembly for L8306-EU
RP005006-FZ Replacement Hose Assembly for L8306FZ
RP005008 Replacement Hose Assembly for L8310
RP005035 Replacement Hose Assembly for L8335
RP005035-FZ Replacement Hose Assembly for L8335FZ
RP005023 Replacement Hose Assem
RP005069 Replacement Hose Assembly for L8345, L8350
RP005049 Replacement Hose Assembly for L8349, L8346
RP005040-FZ Replacement Hose Assembly for L8340FZ
Optional Bench/High Wall
Mounting Bracket
(see FIG. 6)
Model # # of Tension
Turns
3
5
4
4
4
11
bly for L8344