Publicité
Les langues disponibles
Les langues disponibles
Remarque: 1) Une fois la liaison établie, les informations distantes apparaissent sur l'interface du contrôleur ou du
concentrateur. 2) Aucune information distante n'apparaîtra sur l'interface du concentrateur si elle est couplée à Philips Hue
Bridge.
4. TouchLink à un dispositif d'éclairage Zigbee
Étape 1: Configurez le dispositif d'
éclairage zigbee pour démarrer la
mise en service TouchLink.
Reportez-vous à son manuel pour
savoir comment procéder.
Étape 3: appuyez brièvement sur n'
importe quel bouton pour
choisir un groupe de liens
tactiles
Step 4: Press and hold down until
LED indicator turns on.
Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices.
2) TouchLink after both added to a ZigBee network, each remote can link with max. 30 devices.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the remote can control the linked lighting devices.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
6. Factory Reset Manually
Step 1: Press and hold down until
LED indicator turns on.
LED indicator
Step 2: Bring the remote within
10cm of the lighting device.
< 10cm
ZigBee Lighting Device
Step 5: Immediately short press to
start TouchLink commissioning of
the remote. LED indicator flashes
fast for 3S, then flash 6 times slowly
to indicate successful pairing to the
device and the light connected to
the device will blink twice.
From your ZigBee controller or hub
interface, choose to delete or reset
the remote as instructed, indicator
flashes 3 times quickly to indicate
successful removing.
LED indicator
Note: All configuration
parameters will be reset after the
remote is reset or removed from
the network.
Step 2: Immediately short press 5
times continuously, indicator
flashes 3 times quickly to indicate
successful reset.
7. Remove a Touchlink Paired ZigBee Lighting Device
Step 1: Set the Touchlink paired
zigbee device to start TouchLink
commissioning, please refer to its
manual to learn how.
Step 3: Short press the group
button that the device was linked to.
Step 4: Press and hold down until
LED indicator turns on.
8. Factory Reset a Lighting Device (Touch Reset)
Note: the device shall be added to a network, the remote added to the same one or not added to any network.
Step 1: Set the zigbee device to
start TouchLink commissioning,
refer to its manual.
Step 3: Press and hold down until
LED indicator turns on.
9. Find and Bind a Zigbee Lighting Device
Note: Make sure the device and remote already added to the same zigbee network.
Step 1: Start find and bind mode on
the Zigbee lighting device (initiator
node) and enable it to find and bind
target, refer to its manual.
Step 2: Short press a group button
that you would like to bind the
device to.
Step 32: Press and hold down until
LED indicator turns on.
Note: Each remote can bind max. 30 lighting devices.
LED indicator
Step 2: Bring the remote within
10cm of the lighting device.
< 10cm
ZigBee Lighting Device
Step 5: Immediately short press
twice to start TouchLink removing of
the remote. LED indicator flashes
fast for 3S, then flash 6 times slowly
to indicate successful removing.
LED indicator
Step 2: Bring the remote within
10cm of the lighting device.
< 10cm
ZigBee Lighting Device
Step 4: Immediately short press 5
times to start Touch Reset of the
remote. LED indicator flashes fast
for 3S, then flash 3 times slowly to
indicate successful reset.
LED indicator
ZigBee Lighting Device
Step 4: Short press to enable the
remote (target node) to find and
bind initiator.LED indicator flashes
4 times for successful binding or
twice if binding fails.
Publicité
