DA-GEN DRYDEN AQUA GENERATOR Mode D'emploi page 7

110-230 V DRY CONTACT
max. 3.15 A
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Setup and connection of a Variable Speed
Pump, see section 11 - Variable Speed Pump
12.21
12.21 Automatic
In this mode the filtration is controlled by up to 3 timers.
We highly recommend to run your system in a 24/7 mode with a variable speed pump.
For example: During the night time (6:00 until 24:00 & 0:00 until 10:00) in low speed, during day time (10:00 until 6:00) in medium speed.
To set the ON/OFF times select with the up/down keys in the timer line you want to change (1-3 ).
The plus/minus keys open the selected start time field. Set the time with plus/minus keys. Scroll with the up key to the minute field and set it up with
plus/minus keys. To confirm press OK and to cancel press return/escape.
Backwash: See chapter 13
12.31
12.31 Heating: This mode acts equally to the automatic mode, but besides it includes the option to work on a relay to control the temperature.
The system works with a hysteresis of 1 degree (example: the setting temperature is 23° C, the system will activate itself when the temperature
goes below 22° C and will not stop before it passes 23° C).
Use the plus/minus keys to set the desired temperatures
Clima OFF: The heating only works within the set filtration periods.
Clima ON: Keeps the filtration working when the filtration period is finished if the water temperature is below the setting temperature.
* Note: Mode only visible if the temperature probe is installed and/or heating is activated in the "Installer Menu".
13.1
13.1 Backwash Mode with Besgo Valve: The DA-GEN is configured for automatic backwash with Besgo. Use AUX 2!
• Mode:
• Start:
• Interval: Set backwash time in seconds (Recommendation: min. 240 seconds with AFM
• Freq.:
DRY CONTACT
110-230 V
max. 3.15 A
1 2 3 4 5 6 7 8 9 10 11 12 13 14
LIGHT
Lighting control
9 10
&
12. FILTRATION
12.1 Manual mode
N L
A1 A2
14
11
12
FILTER PUMP
7 & 8
Filtration control
12.2 Automatic mode
12.3 Heating mode
13. AUTOMATIC BACKWASH
Choose Auto
Choose starting time
Choose frequency (at least weekly)
14. LIGHTING
14.1
14.4
Only with an external pump controller unit
12.11 12.12
12.11 Filtration:
Configuration control of the filter pump. To set, select
Filtration and confirm by pressing OK. The mode selection
is done in Mode line with the plus/minus keys.
12.12 Manual:
Manually turns ON/OFF the filtration process. No timing
or additional functions. The State (Status) line indicates
whether the filtration pump is ON.
Filter Cleaning: See chapter 13
®
, min. 300 seconds with Sand)
14.2 14.3
14.5
14.5 LED spotlight: In case of installallation of RGB LED lights in the
pool, you can change the color of the lights in the pool. Select the length
of time in seconds in Pulse length and then press Next Program option
to apply the pulse. Refer to your LED spotlight manual to set its different
colors.
6
Without an external pump controller unit
14.1 Lighting
14.2 Manual Mode (ON/OFF). You can activate
the light also by pressing the short cut. You can
set a timer, after that the light will go out.
14.3 Automatic Mode: Switches lights according
to timer settings. Additional you can switch the
lights on by pressing the Shortcut button
EN