Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. D&D Technologies Manuels
  4. Serrures
  5. LOKK Latch
  6. Instructions d'installation

D&D Technologies LOKKLATCH Instructions D'installation

Masquer les pouces Voir aussi pour LOKKLATCH:

Publicité

Liens rapides

Télécharger ce manuel
Installation Instructions
Procedimientos de instalación
Instructions d'installation
POSTE DE LA CERCA
MARCO DE LA PUERTA
FENCE POST
GATE FRAME
4
EXTERNAL ACCESS KIT
7
Extremo curvo
10
Deslizar el cubierta de
fijacion encima de el boton
de oprimir usando las
ranuras de alineacion
Cubierta de fijacion
/ " (4mm)
MAIN LATCH BODY
1
Cercas de metal
P
Madera, Vinilo y Colorbond
B
5
/ " (4mm)
Remache
#
2
JUEGO DE ACCESO EXTERNO
8
11
#
2
#
2
3 / " (90mm)
CAJA PRINCIPAL DEL CERROJO
2
Determinar la dirección correcta
D
/ " (4mm)
#
2
KIT D'ACCÈS EXTÉRIEUR
A lo mas posible situar la Palanca de
Ajuste cerca de el poste de cerca.
Palanca de Ajuste
#
2
/ " (4mm)
SURRURE
3
6
9
12
Cortar cualquier
excedente del pasador
regulador
/
" (6mm)
4
LLINSTR0034PA
Extremo curvo

Publicité

loading

Manuels Connexes pour D&D Technologies LOKKLATCH

Sommaire des Matières pour D&D Technologies LOKKLATCH

  • Page 1 Installation Instructions Procedimientos de instalación Instructions d’installation / ” (4mm) 3 / ” (90mm) MAIN LATCH BODY CAJA PRINCIPAL DEL CERROJO SURRURE POSTE DE LA CERCA MARCO DE LA PUERTA Determinar la dirección correcta FENCE POST GATE FRAME Cercas de metal Madera, Vinilo y Colorbond / ”...

  • Page 2: Installation Instructions

    ENTRETIEN AUSTRALIA: USA: EUROPE: LokkLatch y son marcas comerciales de D&D Group Pty Ltd., registradas en los Estados Unidos LokkLatch and are trademarks of D&D Group Pty Ltd, are registered in USA and elsewhere. y en otros paises. El product esta sujeto a los derechos de patentes y disenos en los Estados Unidos The product is the subject of patent and design rights in USA and elsewhere.
  • Page 3 HINGES Installation Instructions SERIES 3 Hi-Performance Hardware Procedimientos de instalación Regular models - Use 10g screws Heavy Duty models - Use 12g screws Instructions d’installation GATE GAP Level ” (4mm) 2 ALIGNMENT LEG models (L2) ” (6mm) straight edge ” (90mm) ”...
  • Page 4 HINGE RANGE Maximum Maximum Self-Closing Weight Gate Dimensions Maintenance Requirements REGULAR RANGE 66lb (30kg) per pair *5'Hx3'W (1524x915mm) Note: The hinges will operate properly, and warranty is valid, only if installed in HEAVY DUTY RANGE 154lb (70kg) per pair *6'Hx4'W (1830x1220mm) accordance with the instructions and specifications shown herein.

  • Page 7: Fitting Instructions

    FITTING INSTRUCTIONS gate when viewed from inside (house side). gates, please read the instructions overleaf entitled ”– ” (16–19mm) Tools required: Electric drill, drill-bit (to suit masonry), ” (4mm) drill-bit (for pilot holes in thick steel), Phillips No. 2 screwdriver (hand & powered types), level, pencil.
  • Page 8 FITTING INSTRUCTIONS CONTINUED… 18" 24" model model (Upper Bracket) Re-configuring the LokkBolt for Left-Hand Gates 1) Drive the Pin out of the lower end of the stainless steel rod. 3.1/8" (80mm) 2) Remove the Lower Bracket from the rod. Unlock the Lokk-Bolt to release Maximum 9"...