Publicité
Les langues disponibles
Les langues disponibles
Installation
Programming without a Vive Hub
Dimming Module
Part of the Vive Family
Start Here
Associate Wireless Transmitters to
1
Dimming Module
Before beginning this step, make sure that there are no other
Dimming Modules being set up within the same building. It is
possible that wireless transmitters from other systems can be
incorrectly associated to this module.
A On Dimming Module, hold Toggle
button " u " for 6 seconds until
RMJS-5T-347
lights flash.
347 V~ 60 Hz 5 A
0-10 V
The indicator LED will begin
flashing twice per second.
50019280a
B Hold the indicated button on each transmitter for
6 seconds. For dimming loads, lights will flash to show that
wireless transmitters have been associated. For non-dim
loads, lights will not flash.
Link
C On Dimming Module, hold Toggle button " u " for 6
seconds to save association. Lights will flash and LED
will quickly blink for 2 seconds.
D Permanently install wireless transmitters
(consult individual component installation guides for
information).
Reset Factory Defaults
Note: In some instances, it may be necessary to reset the
Dimming Module and connected devices back to factory
default settings. Before beginning, make sure that all devices
are connected and powered.
A Triple-tap the Toggle button " u " on the Dimming Module and
hold until the LED begins to flash slowly; release button.
B Within 3 seconds of the start of flashing, triple-tap the same
button again and the LEDs will flash rapidly indicating that the
unit has been reset to factory defaults.
Note: Any associations or programming previously set up
with the Dimming Module will be erased and will need to be
re-programmed.
Lutron, Pico, Radio Power Savr, and Vive are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. Safari is a trademark of Apple Inc., registered in the U.S. and other countries. All other product names, logos, and brands are property of their respective owners.
©2013 – 2020 Lutron Electronics Co., Inc.
Calibrate the Radio Powr Savr Daylight Sensor
2
Daylight Sensor will control all wired fixtures equally.
A Press and release the "Cal." button on the Daylight Sensor.
B Set lights in room to desired light level.
C Press and hold the "Cal." button for 6 seconds.
D Exit room for 5 minutes to complete calibration.
Note: When calibration has completed, all lights will flash and begin to respond to daylight.
Multiple Daylight Rows (Optional)
For every row of daylighting, a separate Dimming Module must be used. For detailed setup refer to the tuning
section of the Radio Powr Savr Daylight Sensor installation guide.
• Select the Dimming Module that you want to adjust by pressing the toggle button.
Set a Favorite Light Level
(Optional)
3
For Pico remote controls with a Favorite Button.
A Adjust lights to desired level:
lutron.com
Use the Raise button " " or Lower button " " on the Pico remote control.
B Save favorite level:
Press and hold the Favorite button for 6 seconds. The load will flash 3 times
to confirm that the Favorite level is saved.
4
Zero-Second Fade (for Switching Applications)
Cal.
Test
A Cap the violet and pink 0-10 V- wires.
B Press and hold the Raise button "▲" and Lower button " " on the Dimming Module simultaneously for
12 seconds. (The LED will flash to indicate it is now in zero-fade enabled mode.)
See 048753 on www.lutron.com for more information.
5
Set Low-End Trim and High-End Trim
For best results, minimize the amount of sunlight entering the room before performing the following procedures.
Notes
Depending on the fixture manufacturer or load, low-end trim and high-end trim may
need to be adjusted.
• Trim low-end to ensure a stable light level because some loads will flicker or drop out
if trimmed too low.
• Be sure that you can turn on the lights to the low-end trim level without any abnormal
operation.
• The factory default high-end trim is suitable for most applications but can be adjusted
as desired.
Low-End Trim
A Enter low-end trim adjustment mode:
Press and hold the Lower button " " on the Dimming Module for 12 seconds.
The lights will flash and the indicator LED will begin flashing.
B Adjust the low-end trim:
Use the Raise button "▲" and Lower button " " on the Dimming Module to adjust and set the lights to the
desired low-end (1 to 45%).
C Save the low-end trim:
Press and hold the Toggle button " u " for 6 seconds to save setting.
The indicator LED will begin flashing and then turn solid to indicate new level has been saved.
High-End Trim
A Enter high-end trim adjustment mode:
Press and hold the Raise button "▲" on the Dimming Module for 12 seconds.
The lights will flash and the indicator LED will flash.
B Adjust the high-end trim:
Use the Raise button "▲" and Lower button " " on the Dimming Module to adjust and set the lights to the
desired high-end (55 to 100%).
C Save the high-end trim:
Press and hold the Toggle button " u " for 6 seconds to save setting.
The indicator LED will begin flashing and then turn solid to indicate new level has been saved.
Link
Cal.
Test
Raise
Lower
Favorite
(Optional)
RMJS-5T-347
347 V~ 60 Hz 5 A
0-10 V
50019280a
lutron.com
Customer Assistance www.lutron.com/support
Set Minimum Light Level
6
(Optional)
Certain applications (e.g., hallways), may require that the lights never turn off. For these areas, activate
Minimum Light Level mode.
A Enter minimum light level adjustment mode:
Press and hold Toggle button " u " and Lower button " " for 12 seconds. Lights will flash high-low-high and
LED will begin flashing.
If lights stop flashing and go to high-end, the minimum light level is set to OFF (default).
If lights stop flashing and go to low-end, the minimum light level is ON and set to low-end.
B Change the minimum light level:
Press Raise button "▲" to set minimum light level to low-end.
Press Lower button " " to set minimum light level to OFF.
C Save the minimum light level:
Press and hold Toggle button " u " for 6 seconds. LED will quickly flash to indicate that new level has
been saved.
7
Set Occupancy Light Levels
(Optional)
Note: Unoccupied light level is always the minimum light level and cannot be adjusted.
A Set desired occupancy light levels:
Use Raise / Lower buttons "▲ / " on the Dimming Module or Raise / Lower buttons " /
associated Pico Remote Controls.
B Save occupancy light levels:
Press and hold Test button for 6 seconds on any associated Radio Powr Savr Occupancy Sensor without a
Lights On button. Release when Sensor lens starts to flash.
Or, press and hold Lights On button for 6 seconds on any associated Radio Powr Savr Occupancy Sensor.
Release when Sensor lens starts to flash.
See App Note 048753 for instructions on using with non-dim loads.
FCC/ IC Information:
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly
approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
Customer Assistance:
U.S.A. / Canada: 1.844.LUTRON1
www.lutron.com/support
Limited Warranty: www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf
" on all
Publicité
