Lutron Electronics RMJS-5T-347 Manuel D'installation

Vive Installation
347 V~ Dimming Module with 0 –10 V- Control
347 V~ Emergency Dimming Module with 0 –10 V- Control
Part of the Vive Family
RMJS-5T-347 347 V~ 60 Hz 5 A
RMJS-5T-347-EM
0 –10 V- Control: 10 V- 60 mA
(current sink only)
Compatible with ANSI E1.3 2001 (R2006), IEC 60929 Annex E
Important Notes: Please read before installing.
For installation by a qualified electrician in accordance with all local and national
electrical codes.
• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely before installation.
• Operate between 0 °C and 40 °C (32 °F and 104 °F) ambient.
• 0% to 90% humidity, non-condensing.
• For indoor use only.
• For application note, see http://www.lutron.com/TechnicalDocumentLibrary/048753.pdf
For spec submittal, see http://www.lutron.com/TechnicalDocumentLibrary/3691140.pdf
• Class 2 / Class 1 wiring: Install in accordance with all national and local electrical codes.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
• Do not use outdoors.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not be
subjected to tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may
cause an unsafe condition.
• Do not use this equipment for other than its intended use.
SAVE THESE INSTRUCTIONS
Dimming Module
Install in center of room to
maximize RF coverage.
Radio Powr Savr
Occupancy
Sensor
Dimming
9 m
RMJS-5R-347
347 V ~ 60 Hz 5 A Module
(30 ft) max
50019594a lutron.com
Pico
Remote
All Wireless Transmitters Control
must be installed within
12 m (40 ft)
9 m (30 ft) of the
Dimming Module.
Default Functionality
Occupancy Sensors
Occupied: All lights 100%.
Unoccupied: All lights off.
Daylight Sensor
All lights dim in response to daylight.
Link Cal.
Test
Wireless Controls
On All lights 100%
Favorite All lights 50%
Off All lights off
Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036-1299 USA
Required Components
For each system, ensure that you have:
One Dimming Module At least one Wireless Transmitter
Indicator LED
041773
Rev. A
Raise
10/2020
+
RMJS-5T-347
347 V~ 60 Hz 5 A Toggle
0-10 V
Lower
lutron.com
50019280a
Dimming Module (1 maximum) Radio Powr Savr Occupancy / Vacancy Sensor
(10 maximum)
Start Here
Mount, Wire, and Install 0 –10 V- Devices
1
and Lighting Fixtures
Consult third-party device installation guide
WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit
breaker before installing the unit.
A Connect mains wiring (switched hot, neutral) to each fixture.
B Connect 0 –10 V- control (+ and – ) to each fixture.
Green / Yellow
Fixture Earth
Neutral
Switched Line/Hot
+ Violet
– Pink
Note: Violet and pink wires not used for non-dim applications
To additional 0 –10 V- fixtures
NOTE: Output must NOT be used to control receptacles. Output must be directly
connected to the load. Output breakers or switches must not be used.
Wire Connector Information
1/2 in (13 mm): (1-3) 10 AWG (4.0 mm 2 )
1/2 in (13 mm): (1-3) 10 AWG (4.0 mm 2 )
10, 12, & 14 AWG (1-3) 12 AWG (2.5 mm 2 )
Red Red 10, 12, & 14 AWG 13 mm (1/2 in): (1-3) 12 AWG (2.5 mm (1-3) 4.0 mm 2 ) 2 (10 AWG)
Red (4.0, 2.5, & (1-3) 14 AWG (1.5 mm 2 )
(4.0, 2.5, & (1-3) 14 AWG (1.5 mm )
4.0, 2.5, & 1.5 mm (1-3) 2.5 mm 2 (12 AWG)
1.5 mm ) (1-2) 10 AWG & (1) 12 AWG (4.0 & 2.5 mm 2 2 )
2 2
1.5 mm 2 ) (1-2) 10 AWG & (1) 12 AWG (4.0 & 2.5 mm 2 )
(10, 12, & 14 AWG) (1-3) 1.5 mm (14 AWG)
(1-2) 10 AWG & (1) 14 AWG (4.0 & 1.5 mm 2 2 )
5/8 in (16 mm):
(1-2) 10 AWG & (1) 14 AWG (4.0 & 1.5 mm 2 )
5/8 in (16 mm):
(1-2) 12 AWG & (1) 14 AWG (2.5 & 1.5 mm (1-2) 4.0 mm 2 & (1) 2.5 mm 2 )
16 & 18 AWG
16 & 18 AWG 16 mm (5/8 in): (1-2) 12 AWG & (1) 14 AWG (2.5 & 1.5 mm 2 )
(1.0 & 0.75 mm ) (1-2) 10 AWG & (1) 16 AWG (4.0 & 1.0 mm (1-2) 4.0 mm 2 & (1) 1.5 mm 2 )
2
(1-2) 10 AWG & (1) 16 AWG (4.0 & 1.0 mm )
(1.0 & 0.75 mm 1.0 & 0.75 mm 2 ) 2
(1-2) 12 AWG & (1) 16 AWG (2.5 & 1.0 mm 2 )
(1-2) 2.5 mm 2 & (1) 1.5 mm 2
(1-2) 12 AWG & (1) 16 AWG (2.5 & 1.0 mm 2 )
(16 & 18 AWG)
(1-2) 14 AWG & (1) 16 AWG (1.5 & 1.0 mm 2 )
(1-2) 4.0 mm 2 & (1) 1.0 mm
(1-2) 14 AWG & (1) 16 AWG (1.5 & 1.0 mm 2 )
(1-2) 10 AWG & (1) 18 AWG (4.0 & 0.75 mm
(1-2) 2.5 mm & (1) 1.0 mm
2
(1-2) 10 AWG & (1) 18 AWG (4.0 & 0.75 mm 2
(1-2) 12 AWG & (1) 18 AWG (2.5 & 0.75 mm
(1-2) 1.5 mm & (1) 1.0 mm
(1-2) 12 AWG & (1) 18 AWG (2.5 & 0.75 mm 2
2
(1-2) 14 AWG & (1) 18 AWG (1.5 & 0.75 mm
(1-2) 4.0 mm & (1) 0.75 mm
(1-2) 14 AWG & (1) 18 AWG (1.5 & 0.75 mm 2
2
(1-2) 2.5 mm 2 & (1) 0.75 mm
3/8 in (10 mm): (1-3) 12 AWG (2.5 mm 2 )
3/8 in (10 mm): (1-3) 12 AWG (2.5 mm (1-2) 1.5 mm 2 ) 2 & (1) 0.75 mm
12 & 14 AWG (2-3) 14 AWG (1.5 mm 2 )
12 & 14 AWG
(2-3) 14 AWG (1.5 mm 2 )
Yellow
(2.5 & 1.5 mm 2 ) (1-2) 12 AWG & (1) 14 AWG (2.5 & 1.5 mm
2
Yellow Yellow 10 mm (3/8 in): (1-3) 2.5 mm 2 (12 AWG)
(2.5 & 1.5 mm 2 ) (1-2) 12 AWG & (1) 14 AWG (2.5 & 1.5 mm 2 )
(1-2) 12 AWG & (1) 16 AWG (2.5 & 1.0 mm 2
2.5 & 1.5 mm 2 (2-3) 1.5 mm (14 AWG)
7/16 in (11 mm): 2
(1-2) 12 AWG & (1) 16 AWG (2.5 & 1.0 mm 2 )
7/16 in (11 mm): (1-2) 14 AWG & (1) 16 AWG (1.5 & 1.0 mm
(12 & 14 AWG) (1-2) 2.5 mm & (1) 1.5 mm 2
2
16 & 18 AWG (1-2) 14 AWG & (1) 16 AWG (1.5 & 1.0 mm 2 )
16 & 18 AWG
(1-2) 12 AWG & (1) 18 AWG (2.5 & 0.75 mm
(1-2) 2.5 mm 2 & (1) 1.0 mm
(1.0 & 0.75 mm )
2 (1-2) 12 AWG & (1) 18 AWG (2.5 & 0.75 mm 2
11 mm (7/16 in):
(1.0 & 0.75 mm 2 )
(1-2) 14 AWG & (1) 18 AWG (1.5 & 0.75 mm (1-2) 1.5 mm 2 & (1) 1.0 mm
(1-2) 14 AWG & (1) 18 AWG (1.5 & 0.75 mm
1.0 & 0.75 mm 2 2
(1-2) 2.5 mm 2 & (1) 0.75 mm
(16 & 18 AWG)
(1-2) 1.5 mm 2 & (1) 0.75 mm
Troubleshooting
Ballasts or LED drivers cannot be controlled locally from Dimming Module with 0 –10 V-.
Lights do not dim as expected.
Lights do not respond to Wireless Transmitter(s) (Pico remotes and RPS sensors).
Lights are unstable at low-end or flash/flicker at turn-on or turn-off.
Wireless Transmitter(s) cannot be associated to Dimming Module with 0 –10 V-.
Pico Remote Control
(10 maximum)
Install Dimming Module
2
Suggested Installation Location: Center of room to
ensure proper RF coverage of area.
For optimal RF performance: Module must not be fully
enclosed in metal. No metal should exist anywhere
within 200 mm (8 in) in front of the front plate of the
module. Mount a minimum of 0.6 m (2 ft) away from
the controlled fixture. Ensure the junction box is well
grounded (preferably via a metal conduit between the
controlled fixture and the module junction box).
A Dimming Module must be installed in a metal 101.6 mm x
101.6 mm (4 in x 4 in) junction box (minimum depth
54 mm (2.125 in) with mounting screws (provided). Please
consult local and national electric codes for proper installation.
If separation of Class 1 and Class 2 wires in the junction
NEU box is required by code, use Lutron model number
5T-347-DIVIDER (sold separately). In this case it is
Sample recommended, to facilitate installation, that the dimming
HOT
module with the divider be mounted in a separate
ballast shown
junction box. Note: if module cannot be fully seated into the
junction box, try rotating the module 90, 180, or 270 degrees.
+
Or move conduit hardware to a different knockout hole. If neither
–
option works, an extension ring may be required. See 048753 on
www.lutron.com for more information.
B Connect bare copper wire from junction box to green
ground screw.
C
Once installed, energize the Dimming Module.
D
Use the Toggle button " u " to toggle between high-end and OFF
to verify ballasts or LED drivers wiring.
E
Use the Raise "▲" and Lower "
2 (10 & 12 AWG) Programming with a Vive Hub
2 (10 & 14 AWG) 3
2 (12 & 14 AWG)
2 (10 & 16 AWG) The Vive hub can be set-up easily with any
2 )
(12 & 16 AWG)
2
)
2 ) Wi-Fi enabled iOS or Android
(14 & 16 AWG)
) 2
®
)
2
(10 & 18 AWG)
) 2
device.
2 (12 & 18 AWG)
2 (14 & 18 AWG) A Download the Lutron Vive app.
)
)
)
(12 & 14 AWG)
2
2 )
2 (12 & 16 AWG)
)
2 2 ) (14 & 16 AWG)
)
2 (12 & 18 AWG)
2 (14 & 18 AWG)
• Ensure that the breaker(s) to the Dimming Module are energized.
• Ensure that the Dimming Module switched hot lead is wired to the lighting fixture(s).
• Ensure that the Dimming Module control lines are wired to the lighting fixture(s).
• Ensure the driver is a current source for the 0-10 V- link.
• Dimming Module may be in emergency mode.
Reset to factory defaults.
• Ensure that 0 –10 V- control lines are wired properly.
• Ensure that fixture does not require an inverted signal (10 – 0 V- control).
• Ensure the driver is a current source for the 0-10 V- link.
• Dimming Module may be in emergency mode.
• Ensure that the breaker(s) to the Dimming Module and any connected ballasts or LED drivers are energized.
• Ensure that Wireless Transmitters are associated to the Dimming Module.
Reset to factory defaults.
• Adjust low-end trim.
• The maximum number of Wireless Transmitters have been associated to the Dimming Module. To remove a previously set up Wireless Transmitter, tap a Wireless
Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
Customer Assistance www.lutron.com/support
At least one 0 –10 V- Fluorescent Ballast or LED Driver
Consult third-party 0 –10 V- fixtures installation guide for fixture-specific wiring.
+
Link Cal.
Test
60 mA maximum for the control lines. Switches up to 5 A total.
Radio Powr Savr Daylight Sensor
Note: All drivers and ballasts used with Vive wireless controls must comply with the
(1 maximum)
limits pursuant to CAN ICES-005 and the FCC rules.
200 mm
(8 in)
200 mm RMJS-5T-347 200 mm
Keep metal
347 V~ 60 Hz 5 A
0-10 V
(8 in) at least
(8 in)
200 mm
(8 in) away
50019280a lutron.com
200 mm
(8 in)
" buttons to verify control wiring.
B Open the app and follow the instructions.
compatible
®
vive.lutron.com X
Junction Box
200 mm
(8 in)
Line / Hot (Black)
Switched Line / Hot (Red)
200 mm
Neutral Neutral (White) To Fixtures
(8 in)
200 mm
RMJS-5T-347
(8 in)
347 V~ 60 Hz 5 A
0-10 V
50019280a lutron.com
0 –10 V- to Fixtures
– (Pink)
(cap wires for non-dim
+ (Violet)
applications)
Note: RMJS-5T-347-EM requires the use of an automatic transfer
switch to change from normal to emergency power. Refer to 048628
for wiring diagrams on www.lutron.com
If installing an emergency Dimming Module and the wiring needs
to be verified, follow "Reset Factory Defaults" procedure to exit
emergency mode.
Please note that any programming will be lost and will have to be
reprogrammed. Only perform this step during initial installation and
wiring verification.
Note: For periodic testing and maintanance of emergency systems,
use the toggle button to ensure proper operation. Make sure buttons
remain accessible.
Note: Momentary power outages can envoke emergency mode on
the dimming module. SeeTroubleshooting section for details.
Note: For further information on set up,
programming, and troubleshooting with a
Vive system, please refer to the installation
instructions included with the Vive hub or visit
www.lutron.com/vive
Note: For programming the Dimming Module
without a Vive hub see reverse side.
www.lutron.com/support