Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION
1.
Make certain that the fixture has been de-energized before
any changes are made to the system.
2.
Remove the Appleton luminaire from the top hat according
to the Appleton removal instructions. Questions regarding
the removal of the Appleton products should be directed
towards Appleton customer service. Inspect the Appleton
top hat seal surfaces for damage.
3.
Ensure that all gaskets and sealing surfaces are clean and
free of debris. Wipe with a damp lint free cloth and then dry
fully before installation.
4.
Install the CHMM1 Adapter onto the ballast housing or
LED driver housing of the Crouse-Hinds Champ® Series
luminaire by capturing the luminaire's hinge pin inside
the adapter hinge hook, as shown in Figure 1. Ensure the
adapter is concentric to the luminaire as you clamp the
adapter down. Thread the captive closing screw into the
adapter, and tighten it to 30 in.-lbs (3.4 N-m).
5.
Secure one end of the CHMM1 Adapter ground lead to the
luminaire ground lead using methods that comply with all
applicable codes.
6.
Hang the assembled luminaire and adapter from the
Appleton top hat by capturing the adapter hinge pin in the
Appleton top hat hook, as shown in Figure 2.
7 .
Ensure that the Appleton top hat is connected to earth
ground. Connect the remaining free end of the CHMM1
Adapter ground lead to the Appleton top hat. Ensure that the
CHMM1 ground lead is securely fastened to the appropriate
ground leads or lugs supplied with the Crouse-Hinds
luminaire and Appleton top hat.
8.
Connect supply wires per the appropriate luminaire IF sheet
using methods that comply with all applicable codes. Tighten
all electrical connections.
9.
Seal the adapter onto the top hat by swinging the adapter
towards the top hat and engaging the swing bolt, making
sure that all wires are safely inside and positioned
appropriately per the luminaire instruction IF sheet. Tighten
the swing bolt to 79 in-lbs (8.9 N-m).
10. Continue as needed with installation of luminaire per the
respective luminaire instruction IF sheet.
11. Turn power on and verify proper operation of the luminaire.
MAINTENANCE
•
Perform visual, electrical, and mechanical inspections on
a regular basis. The environment and frequency of use
should determine this. However, it is recommended that
checks be made at least once per year. We recommend an
Electrical Preventative Maintenance Program as described
in the National Fire Protection Association Bulletin NFPA
No. 70B: Recommended Practice For Electrical Equipment
Maintenance (www.nfpa.org).
•
The luminaire and adapter should be cleaned periodically
to ensure continued performance. To clean, follow the
instruction IF sheet for the respective fixture. The adapter
All statements, technical information and recommendations contained herein are based on information and tests we believe to be
reliable. The accuracy or completeness thereof are not guaranteed. In accordance with Eaton's Crouse-Hinds Business "Terms and
Conditions of Sale," and since conditions of use are outside our control, the purchaser should determine the suitability of the product
for his intended use and assumes all risk and liability whatsoever in connection therewith.
•
•
•
•
REPLACEMENT PARTS
Crouse-Hinds CHMM1 Top Hat Adapter does not have
any regularly replaceable parts. Should the adapter break or
otherwise become unusable a complete replacement assembly
should be used. Assistance may also be obtained through your
local Eaton's Crouse-Hinds Business representative.
Eaton's Crouse-Hinds Business
Sales Service Department
P.O. Box 4999
Syracuse, New York 13221
Phone (315) 477-7000
Eaton's Crouse-Hinds Business
1201 Wolf Street Syracuse, New York 13208 • U.S.A.
Copyright© 2014
may be cleaned using a clean damp cloth. If this is not
sufficient, use a mild soap or a liquid cleaner such as
Collinite NCF or Duco #7. Do not use an abrasive, strong
alkaline, or acid cleaner. Damage may result. Consult
Appleton for maintenance and cleaning of the top hat.
Visually check for undue heating evidenced by discoloration
of wires or other components, damaged parts, or leakage
evidenced by water or corrosion in the interior. Contact
Crouse-Hinds for replacement part information.
Electrically check to make sure that all connections are
clean and tight.
Mechanically check that all parts are properly assembled.
Do not loosen or remove Top Hat swing bolt after
installation. Joint between CHMM1 Adaptor and Appleton
Top Hat shall be considered permanent after installation.
IF 1682
Revision 2
Revised 04/14
Supersedes 11/13
Publicité
