Kichler 42017NI Instructions D'assemblage Et D'installation

INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L'assemblage et L'installation Au Canada
IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turn off and allow to cool before replacing bulb.
• Bulb gets HOT QUICKLY! Contact switch only when turning off.
• DO NOT remain in light if skin feels warm. (Light is intense, may cause "sunburn")
• DO NOT look directly at lighted bulb.
• Keep materials away from bulb that may burn.
• Use ONLY with wattage specified or lower.
• DO NOT touch bulb at any time, use a soft cloth. Oil from skin may damage bulb.
• DO NOT operate fixture with missing or damaged glass.
LOOP/CHAIN LINK MOUNT
1) Pass wire through stems and screw stems into couplings on top of fixture
body. NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (3) to prevent accidental rotation of fixture during cleaning,
relamping, etc.
2) Pass fixture wire through remaining stems and screw stems together.
3) Thread one small threaded pipe into end of each small loop.
4) On each side of fixture, pass fixture wire from last stem through first loop.
Thread each first loop onto end of each last stem.
5) On each side of fixture, pass fixture wire through each small loop on canopy
and through hole in canopy.
6) Attach one chain link to small loop at end of each stem and to each small oop
on canopy.
7) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work without shutting off
the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the "OFF" position.
b) Unscrew the fuse(s), or switch "OFF" the circuit breaker switch(s), that
control the power to the fixture or room that you are working on.
c) Place the wall switch in the "OFF" position. If the fixture to be replaced
has a switch or pull chain, place those in the "OFF" position.
8) At the center of the backpan are knockout slots. Remove the set that matches
your outlet box.
9) Secure the backpan to the outlet box.
10) Anchor the backpan to the ceiling using the set of holes at each end of fixture
using wood screws, toggle bolts, plastic anchors, etc.
11) Connect fixture ground wire to outlet box ground wire with wire connector.
Never connect ground wire to black or white power supply wire.
12) Make wire connections (connectors not provided.) Reference chart below for
correct connections and wire accordingly.
Connect Black or
Red Supply Wire to:
Black
*Parallel cord (round & smooth)
Clear, Brown, Gold or Black
without tracer
Insulated wire (other than green)
with copper conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Date Issued: 12/11/15
BOUCLE/MAILLON DE CHAÎNE
BACKPAN
PANNEAU ARRIÈRE
CANOPY
CACHE
CHAIN LINK
MAILLON DE CHAÎNE
3
STEM
3
TIGE
3
3
3
Connect
White Supply Wire to:
White
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with silver conductor
Neutral Wire
LOOP/CHAIN LINK
BOUCLE
THREADED CAP
BOUTON MOLETÉ
13) Carefully push wire connections back into outlet box making sure all connections
remain secure.
14) Slip canopy over mounting screws and backpan. NOTE: Be certain wires do
not get pinched between backpan and canopy.
15) Secure canopy to backpan using threaded caps.
16) Set glass down over socket.
17) Attach socket ring to socket ring tool. Thread socket ring onto socket. (DO NOT
over tighten.)
18) Insert recommended bulb. CAUTION: DO NOT touch bulb with bare hands. If
this happens, clean bulb with denatured alcohol and a lint free cloth.
19) Carefully slip glass sleeve over bulb. Thread glass sleeve onto socket. (DO
NOT over tighten.)
1) Remove each small loop from the canopy. NOTE: The lockwashers and
hexnuts will be used in step 5.
2) Remove threaded pipe from each small loop.
3) Pass wire through stems and screw stems into each coupling on top of fixture
body. NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (3) to prevent accidental rotation of fixture during cleaning,
relamping, etc.
4) Pass fixture wire through remaining stems and screw stems together.
5) On each side of fixture, pass fixture wire through the small threaded pipe
removed from each small loop. Thread one small threaded pipe into end of last
stem on each side of fixture.
6) On each side of fixture, pass fixture wire through each hole in canopy. Lower
canopy down towards stems. Pass each hole in canopy over end of threaded
pipes on each last stem.
7) On each side of fixture, pass fixture wire through hole in one lockwasher. Thread
one lockwasher onto each threaded pipe protruding from inside canopy.
8) On each side of fixture, pass fixture wire through hole in one hexnut and
thread each hexnut onto end of threaded pipe.
9) Follow steps 7-19 in Loop/Chain Link/Loop Installation Instructions.
INSTALLATION SUR TIGE CANNELÉE
CANOPY
CACHE
SEE OTHER SIDE FOR CANADIAN FRENCH TRANSLATIONS.
VOIR L'AUTRE CÔTÉ POUR LES CANADIENS TRADUCTIONS EN
FRANÇAIS.
We're here to help
LOOP
GLASS SLEEVE
MANCHON DE
VERRE
BULB
L'AMPOULE
SOCKET RING TOOL
ANNEAU DE LA DOUILLE
SOCKET RING
ANNEAU DE LA DOUILLE
GLASS
VERRE
RIGID STEM MOUNT
RIGID STEM MOUNT
866-558-5706
Hrs: M-F 9am to 5pm EST
BACKPAN
PANNEAU
ARRIÈRE
STEM
TIGE
IS-42017-CB