Table des Matières
Publicité
14
| English
IDENTIFICATION
1. Handle
2. Power cord hook
3. Switch ON/OFF
4. Power cord
5. Water outlet
6. Wheel
7. High-pressure hose hook
8. High-pressure hose
9. Trigger gun
10. Trigger gun hook
11. Rear case
12. Detergent tank
13. Spray lance
14. Water inlet
15. Release trigger gun button
ASSEMBLY
A. Slide the handle into position with two screws.
B. Slide the trigger gun holder into position.
C. Slide the power cord hook into position.
D. Assembling the trigger gun - spray lance.
E. Connect the high pressure hose to the trigger gun.
F. Disconnect the pressure hose.
G. Connect the high-pressure hose to the water out-
let of the machine.
H. Connect the garden hose to the water inlet.
ATTENTION! ALWAYS USE A WATER FILTER.
Connect the water supply.
ATTENTION! Impurities in the water can damage
the high-pressure pump and the accessories
USE WITH ALTERNATIVE WATER SOURCES
The power washer is self-priming and enables wa-
ter to be drawn in from containers or natural water
sources. It is IMPORTANT that the water filter is in
clean condition when inserting it at the water inlet,
and that only clean water is drawn in.
OPEN TANKS/CONTAINERS AND NATURAL WA-
TER SOURCES
Use the Self Priming accessory kit comprising:
Inlet strainer with non return valve
ƒ
3m reinforced supply hose
ƒ
Universal coupling to the pressure washer
ƒ
This enables the pressure washer to draw water up to
0,5m above the water level in the source in approxi-
mately 15 seconds.
Fully immerse the 3m hose into the water to displace
the air in the hose. Connect the 3m hose to the power
washer and make sure that the inlet strainer remains
under water.
With the spray gun removed, switch the power wash-
er on and operate it until water flows uniformly out of
the high-pressure hose. If no water is coming out of
the high-pressure hose after 25 seconds, switch the
power washer off and check all connections. As soon
as water flows out of the high-pressure hose, switch
the power washer off and connect the gunand lance
to begin with the work.
It is important that hose and couplings are of good
quality and are tightly connected, and that the seals
are undamaged and properly inserted. Loose connec-
tions can impede the priming.
OPERATION
ATTENTION! Dry running of more than 2 minutes
leads to damage of the high-pressure pump. If
the appliance does not build up pressure within 2
minutes, switch the appliance off and proceed in
accordance with the instructions in Chapter "Trou-
bleshooting".
HIGH PRESSURE OPERATION
CAUTION! Keep a distance of at least 30 cm when
using the jet for cleaning painted surfaces to avoid
damage.
CAUTION! Make sure the ON/OFF switch is set to
"OFF/O" and insert the plug into a properly installed
socket.
ATTENTION! The washer must be used on a secure
and stable surface in a standing, upright position.
Connect the product to power and water supply as
described.
Open the water supply.
ƒ
Hold the trigger gun with both hands.
ƒ
Direct the nozzle away from you towards the sur-
ƒ
face to be cleaned.
Note: Make sure that the release trigger gun button
(15) is on the position unlock so the trigger can be
pressed.
Unlock the trigger and press it until a constant
ƒ
amount of water flows through the nozzle, to allow
air trapped in the hose to escape (I).
Release the trigger.
ƒ
Turn the switch "ON/OFF" on the position "ON/I"
ƒ
(J).
Hold the trigger gun with both hands. Direct the
ƒ
water jet to the object to be cleaned and press the
trigger.
Release the lever of the trigger gun; the device will
switch off again and stop the water jet. High pressure
remains in the system.
WARNING! Beware of kickback when pressing the
trigger!
Note: During longer breaks (more than 5 minutes),
also turn the appliance off using the "ON/OFF" switch.
OPERATION WITH DETERGENT
Only use cleaning agents suitable specifically for high
pressure washers. We recommend that you use de-
tergent sparingly for the sake of the environment.
Observe the recommended dilution on the detergent
label.
Detergent can only be added when the device is oper-
ated in low pressure mode.
DANGER! When using detergents, the material data
safety sheet issued by the detergent manufacturer
must be adhered, especially the instructions regard-
ing personal protective equipment.
Remove the cap of the clean detergent bottle. Gently
pull the on board detergent tank out of its storage
position.
Fill the tank with detergent designed specifically for
use with pressure washers (K).
Assemble the detergent tank (12) on the trigger gun
(9)(L).
HPW 100 EASY
Publicité
Table des Matières
