5.4 TO CONTROL ROTARY PUMP WITH ENCODER MOTOR
Procedures to control the Rotary Pump with encoder motor are very similar to
procedures to control the standard Rotary Pump. The encoder count values is
ranging from 1 to 60,000 counts.
5.4.2
Connecting The Unit: Refer to Figure 6.0 for details
1. Connect the power cord, foot switch and air hose to the back of the unit.
2. Connect Encoder Motor Cable to Port C.
Note: Encoder motor cable, TSECABLE, must be purchased separately.
3. Connect syringe air hose to Port B (regulated, pulsed air signal).
If constant air pressure is required, connect syringe air hose to accessory
air outlet port located in the rear of the unit, port #13 in figure 1.0
4. Press the Power button (1) to turn on the unit.
5. Press the Mode (2) and Set up button (3) simultaneously until "PUMP-E"
appears on the top right hand corner of the Display.
Program # Cycle Mode
P1 TIMED MODE PUMP-E
Input Voltage
20.000V
Encoder Count
10000P
Reverse
1P
Encoder Count
Figure 8.0
5.4.2 Program Selection: Follow steps in Section 5.3.2
5.4.3 Manual/Purge Dispense Cycle: Follow steps in Section 5.3.3
5.4.4 Automatic Dispense Cycle Setting: Follow steps in Section 5.3.4
5.4.5 Iteration for Encoder Count Setting
The maximum default encoder count is 60,000P. However there is an
ITERATION "Itr" feature that can be used to increase the dispense
duration up to 4 times (240,000 counts) without interruption.
1.
Press and hold the Setup button (#3) for 2 seconds to enter setup
screen
2.
Press both Power button (#1) and Mode button (#2) simultaneously (3
times) until "Itr" appear.
3.
Press both the Setup button (#3) and (+) button simultaneously to
increase iteration.
4.
Press both the Setup button (#3) and (-) button simultaneously to
decrease iteration
5.
Press the Setup button (#3) to save data and return to main screen.
Control Type
1
Counter
15 PSI
Pressure Port A (not use)
15 PSI
Pressure Port B
Regulated
10
8. Active la presión de aire atomizada girando la perilla del Regulador de
aire a presión (6) hasta que se indique la presión deseada en la Pantalla.
Nota: La presión en el Puerto A puede monitorearse con la
configuración de baja presión, pero no se regula con el regulador de
aire de la unidad. Emite la misma presión que la presión de entrada. Por
otra parte, la presión en el Puerto B se regula, pero no está conectada a
la configuración de baja presión.
9. Mantenga presionado el interruptor de pedal para activar el ciclo de
pulverización.
5.2.4 Configuración del ciclo de dosificación automática:
1. Presione el botón de modo (2) para seleccionar "TIMED MODE" (Modo
Tiempo) o el modo "INTERRUPT" (Interrumpir).
2. Mantenga presionado el botón de ajuste (3) durante dos segundos para
ingresar en la pantalla de configuración. Se resaltará el último dígito del
tiempo de Pulverización/tiempo de dosificación (DISP).
3. Presione el botón (+) o (-) para ajustar el tiempo.
4. Mantenga presionado el botón de ajuste (3) durante dos segundos para
mover el cursor al tiempo de Pulverización previa (PRE) y repita este paso
para pasar al tiempo de Pulverización posterior (POST).
5. Presione el botón de ajuste (3) para mover el cursor a la siguiente
posición.
6. Presione el botón (+) o (-) para ajustar el tiempo
7. Mantenga presionado el botón de ajuste (3) durante dos segundos para
guardar los datos.
8. Si la unidad está en "TIMED MODE" (Modo Tiempo) presione y suelte el
interruptor de pedal para activar el ciclo de pulverización.
9. Si la unidad está en modo "INTERRUPT" (Interrumpir), mantenga
presionado el interruptor de pedal hasta que se haya completado el ciclo de
dosificación. El ciclo de dosificación puede interrumpirse si se suelta el
interruptor de pedal, y reanudarse cuando vuelve a presionarse el
interruptor de pedal.
5.3 CONTROL DE LA BOMBA ROTATIVA TS5000 ESTÁNDAR
PRECAUCIÓN: Debe instalarse un filtro de 5 micras (TSD800-6) con la unidad para
garantizar un filtrado correcto del aire.
TO AIR SOURCE
9
6
Figura 6.0
10
4
5
8
7
1
2
3
63