Horizon Global 118831 Directives De Montage

Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Tesla Model Y
WARNING
ALWAYS read and follow all warnings and
instructions included with purchase before
beginning installation. Keep for future reference.
DO NOT exceed lower of towing manufacturing
rating (including in your vehicle owner's manual)
or specific amperage ratings stated on product.
ALWAYS read, understand and follow all
warnings and instructions printed on tow
vehicle's battery.
ALWAYS wear safety glasses and use all safety
precautions during installation.
118831-037 Rev. A
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket & Ratchet or
10mm Wrench, Drill (3/32" Drill Bit), Wire Crimpers,
Wire Cutters, Philips Head Screwdriver, Test-probe
1. Open hatch to locate the vehicle wiring inside the
vehicle's rear cargo area by partially removing the
plastic threshold cover, side panels, and cargo
trays, exposing the vehicle's taillight wiring
A
harness.
WARNING
Never cut into or attached any power wire or device
to the high power orange line, cables or connectors.
Serous injury can result.
2. On the driver's side, insert the T-One
end, with the yellow wire, between the vehicle
wiring connectors and lock into place. Be careful
not to damage the locking tabs and be sure that
connectors are fully inserted with locking tabs in
B
place.
3. On the Driver's side, mount the T-One
black box using the double-sided tape provided.
Secure the remainder of the T-One
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid any
areas that would cut or pinch the wire.
4. WARNING
Verify what is behind any surface prior to drilling to
avoid damage to the vehicle and/or personal injury.
Do not drill into any exposed surfaces.
WARNING
Never cut into or attached any power wire or device
to the high power orange line, cables or connectors.
Serous injury can result.
A
11/2/20
B
Locate a suitable grounding point near the
connector such as an existing ground stud or drill
a 3/32" hole and secure the white wire using the
eyelet and screw provided. (Do not drill into vehicle
floor or bed.) Clean dirt and rustproofing from area.
5. Route the T-One
the passenger's side behind the panels and along
the threshold to the taillight pocket.
6. On the passenger's side, insert the T-One
Connector end, with the green wire, between the
vehicle wiring connectors and lock into place. Be
careful not to damage the locking tabs and be sure
that connectors are fully inserted with locking tabs
in place.
7. Remove cover, to access battery T-one power
Connector
®
connection point.
WARNING
Never cut into or attached any power wire or device
to the high power orange line, cables or connectors.
Serous injury can result.
Disconnect the vehicle's Negative (-) battery cable.
Connector
®
If not removed, remove the fuse from the yellow
fuse holder (provided). After cutting the fuse holder
Connector
®
wire, attach the ring terminal and secure to the
vehicle's Positive (+) battery cable. Connect the
other end of the fuse holder to the black 12 ga.
B
wire, using the yellow butt connector (provided).
8 . Either route the black wire thru a grommet and
along the exterior frame or follow the existing
wiring along the thresholds into the engine
compartment up to the battery avoiding areas that
may pinch or break the wire.
Connector end with green wire to
®
C
®
De
C
d
e
9. WARNING
Read and follow all warnings and cautions printed
on the tow vehicle's battery. All connections must
be complete for the T-One Connector to function
®
properly. Test and verify installation with a test light
or trailer once installed. For initial test, reset vehicle
electrical system by temporarily removing the key
from the ignition.
10. Reconnect the vehicle's Negative (-) battery cable
and install the 15 amp fuse into the fuse holder
from step 10.
11. Reinstall the plastic trim panels, threshold, storage
covers, floor covering and other items that may
have been removed during installation, being
careful not to pinch or cut the wires.
NOTE
Route the 4-Flat through the driver's side trim panel
into storage compartment on the threshold and
store there when not in use.
WARNING
Overloading circuits can cause fires. DO NOT
exceed stated product ratings. Read vehicle's
owner's manual & instruction sheet for additional
information.