INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS FOR COOKER HOOD
Exhausting cooker hood. The equipment is constructed in accordance with European Standards and with the requirements included in the following
Directives: 2006/95EC (Low Voltage Directive), 2004/108 (Electromagnetic Compatibility).
WARNINGS
The present instruction manual is an integral part of the appliance itself, therefore it must be carefully kept and ALWAYS accompany it, even in case
of its assignment to another owner or user or in case the cooker hood is moved to another installation plant.
Make sure that the voltage (V) and frequency (Hz) indicated on the data plate inside the unit match those available at the installation site. Any eventual
adjustment to the electrical system, which may be necessary to install the cooker hood, must be carried out only by competent people.
Any repair carried out by no competent people may cause damages.
For any repair or needed technical action make reference to a Technical Assistance Centre, which is authorized to carry out the replacement of the
spare parts. Always make sure that all the electrical parts (lights, exhaustion unit) are disconnected when the appliance is not in use. By storms take
off the main switch of the house electrical system (Fig. 1) or if the device is equipped with a plug, simply unplug it from the mains socket (Fig. 2).
This product can be installed at reduced distances from the hob compared to a normal kitchen hood. In this condition, the heating of all the surfaces
of the hood, even those inside the cabinet, is completely normal and is not a sign of malfunction. Heating is accentuated if the hood is installed above
a gas hob. It is therefore recommended not to store flammable material above the hood body inside the wall cabinet.
The using of the cooker hood must not be other than the use of exhausting units for cooking damps on domestic kitchens.
The manufacturer does not accept any liability for damages caused by people, animals or things, by installation and maintenance mistakes or by any
illegitimate use.
We remind that the use of products functioning with electrical energy implies the observance of some essential security rules, as follows:
This equipment is not intended for people (children included) with reduced mental or motor capacities, with lack of experience or knowledge,
unless they are supervised or unless a person responsible for their security, gives them instructions regarding the use of the equipment.
Children must be supervised in order to be sure that they do not play with the equipment.
Any cleaning action is forbidden if the appliance hasn't been disconnected from the main power supply and if the main switch of the house
electrical system is not off (Fig. 1) or if the device is equipped with a plug, simply unplug it from the mains socket (Fig. 2). If cleaning is not
carried out according to these instructions, a fire may break out.
Do not pull, take off or twist the cable coming out from the appliance, even though this has been disconnected from the main power supply.
Do not sprinkle or throw any water directly on the appliance.
Do not stick any sharp tool inside the exhausting holes and into the air discharge.
Do not take out the filters in order to reach the internal sides of the appliance in case the main switch of the house electrical system is not
off.
Do not singe or flambé directly underneath the cooker hood. Take particular care when frying to ensure that the oil does not catch fire.
CAUTION: Accessible parts may become hot when used with cooking appliances.
It is forbidden to use the hood as a support surface unless it is expressly indicated.
Only use the fixing screws supplied with the product for installation.
This appliance is marked in accordance with the European Directive 2012/19/EC, Waste Electrical and Electronic Equipment (WEEE).
The symbol on the product or on the packaging indicates that the product should not be considered as a normal household waste,
but must be taken to the appropriate collection point for the recycling of electrical and electronic equipment.
By appropriately dispose of this product, it helps to avoid potential negative consequences for the environment and health that may
result from inappropriate disposal of the product.
For more detailed information on recycling this product, contact your local office, local waste disposal service, or the shop where you
purchased the product.
USE
This hood has been designed to work exclusively in filtering mode.
The aspirated fumes pass through the Plasma filter and are re-introduced into the kitchen without odors. If necessary, connect a pipe to the engine
outlet to expel the intake air out of the cabinet. The pipe must have the same diameter as the motor output and must have smooth internal surfaces.
INSTALLATION
Read the instruction manual before installing and/or using the hood.
In order that the minimum distance between the support surface of the cooking vessels in a gas hob and the low voltage components present in the
hood is at least 65cm. as required by current legislation, the lower part of the hood should be no less than 50cm away from these supports. If the
installation instructions for the gas hob indicate a greater distance, it must be taken into account. (Fig. 4).
It must not be superimposed on stoves with an upper radiating plate.
Respect all the air discharge regulations.
The air must not be discharged in a pipe used to discharge exhaust fumes produced by gas-fed equipments or fuel-fed equipments (this does
not apply to filtering hoods).
The room must be adequately ventilated when the hoods is used together with other gas or fuel equipments.
The hood placed above an induction hob can cause condensation, this is a normal phenomenon and not due to malfunctioning of the product.
For an easy access, it is advisable to move possible furniture under the installation area.
For the installation of this hood, the minimum internal height of the cabinet must be at least 46cm. (Fig. 4)
The hood is provided with a steel telescopic rear spacer. This is intended to adapt the depth of the hood to that of the wall unit (from 30cm to 35cm).
Extract the spacer from the hood until you reach the depth of your wall unit and fasten it to the hood with the supplied screws (Fig. 5)
To fix the back of the cabinet to the hood, use the supplied backrest lock. Adjust the position of the backrest stop according to the position of the back
of your wall unit and fix it with the supplied screws as indicated in (Fig. 6)
Remove the grease filters, insert the hood into the cabinet and fix it with the supplied screws (Fig. 7).
The hood is equipped with all the necessary fastenings for its installation, which are suitable for most surfaces. Verify that the installation surface is
strong.
Installation must be carried out by qualified installers according to present regulations.
MOD. ARIA-IN
230-240 Vac – 50 Hz
5
EN