blackburn OUTPOST REAR Instructions De Montage

OUTPOST
REAR
Rack / Porte-bagages
2 x Extenders / Rallonges
300mm
2 x
Cam Lock / Verrou à came / Zylinderschloss
2 x
Eyelete / Œillet / Öse
2 x Bolts / Boulons / Bolzen
16mm M5
2 x Swivel Bolts / Boulons pivotants / Schwenkriegel
18mm M5
2 x Swivel Bolts / Boulons pivotants / Schwenkriegel
25mm M6
Concave Washers / Rondelles concaves /
2 x
Konkav-Unterlegscheiben
2 x Seat Stay Clamp - Smaller / Attache de hauban – petite /
Sattelhalterungsklemme – klein
2 x Seat Stay Clamp - Larger / Attache de hauban – grande /
Sattelhalterungsklemme – groß
2 x
Nylock Nut / Écrou / Mutter
1 x Allen Key / Clé hexagonale /
Sechskantschlüssel
4mm M6
STEP 1 - Option 1
M5 Bolt
M5 Bolt
STEP 1. ATTACH STRUTS: The lower mount of
this rack is designed to attach to bicycle using
either M5 bolts (supplied, Option 1) or with an
extra long quick release (available separately
#7051904, Option 2).
Option 1. Spread rack struts to t on the outside
of the bike frame. Attach rack to lower "braze
ons" with supplied M5 bolts. Do not fully tighten.
Option 2. This option allows for the tment of
racks if a lower "braze on" is not available.
Remove rear quick release. Spread rack struts to
t on the outside of the dropouts. Install extra
long quick release (available separately) through
the lower mount and bicycle hub. Follow your
bicycle/wheel manufacturer recommendations for
removing and installing quick release or have a
quali ed bicycle shop replace it for you.
STEP 2. ADJUST HEIGHT: The lower mounts
allow for optimization of the height of the rack to
accommodate tire sizes ranging from 26" x 1.25"
to 29" x 2.35" (which would include all 700c tires).
There are ve height settings that allow the rack
to move up or down. To adjust the height, remove
the concave M5 bolt on each side of the lower
mount. Slide the rack up or down and reinstall the
concave bolt (torque value) on lowest setting that
allows at least 20mm between the tire and rack.
Warning: Periodically check all nuts and bolts for tightness.
Avertissement: Véri er régulièrement que tous les boulons et écrous soient bien serrés.
Warnung: Überprüfen Sie regelmäßig, dass alle Schrauben und Muttern fest sitzen.
™
STEP 1 - Option 2
Nut
Extra long quick release
*Available separately
STEP 3. ATTACH EXTENDERS: There are three
options available to attach the extenders
depending on the bicycle setup.
Option 1. For bikes with seat stay "braze ons."
Place the cam lock onto one side of the front rack
strut and slide the extenders through the cam lock
holes with the straight end toward the front of the
bike. Attach the extender to the frame "braze on"
using the supplied M5 swivel bolt and concave
washer. Do not tighten. Adjust rack until top is level
with ground by sliding it on the extender. Once
level, tighten cam lock bolt. Repeat this step on
the other side of the rack strut.
Option 2. If Option 1 is not available, then use the
cantilever brake mounts.
Remove the eyelet from the straight end of the
extender and install on the opposite end with 90
degree bend. Place the cam lock onto one side of
the front rack strut and slide the upper mount
through the cam lock holes with the 90 degree
bend end toward the front of the bike. Remove the
bicycles cantilever brake mount bolt and attach the
extender to the frame brake mount using the
supplied M6 swivel bolt and concave washer. Do
not tighten. Adjust rack until top is level with
ground by sliding it on the extenders. Once level,
tighten cam lock bolt. Repeat this step on the
other side of the rack strut.
STEP 3 - Option 1 STEP 3 - Option 2
M5
Concave
Swivel
Washer
Bolt
STEP 3 - Option 3
Concave
Washer
M6
Swivel
Bolt
Swivel
Bolt
Option 3. MTN & Recreational.
If Option 1 and 2 are not feasible, then use vinyl
coated seat stay clamps (2 sizes included).
Attach with 10mm bolts and nylock nuts.
STEP 4. TRIM UPPER MOUNTS: Mark each
of the upper mounts approximately 10mm
behind the cam lock. Remove the upper mount
one at a time and cut at the mark with a
hacksaw or pipe cutter. Gently le any rough
edges from cutting the extender. Reinstall the
upper mounts following the instructions in
Step 2.
STEP 5. TIGHTEN BOLTS: Tighten each of
the bolts attached during the previous Steps
according to the bike and/or component
manufacturer¹s speci cations.
Go to www.blackburndesign.com for updates
on this document.
© 2014 Bell Sports, Inc.
Customer Service: 1-800-456-2355
Printed in China
blackburndesign.com
Vinyl Clamps
(for bikes without
braze-ons)