Publicité
Fig. 2 - Option de Montage Encastré – Modèles 130** et 140**
(4) VIS N°6 X 1-1/4
po FOURNIES
Fig. 3 - Option de Montage en Surface – Modèles 132** et 142**
INSTALL BEHIND CONDUIT
SPACER/WALL GASKET
SPACER
Fig. 4 - Option de Montage Encastré Fermé – Modèles 133** et 143**
(2) PROVIDED
BREAK OFF ALL (4)
OF THE CONDUIT
WINDOWS AND
TABS THEN TRIM
BREAK OFF ALL (4)
SHARP EDGES
BEFORE INSTALLATION
OF THE CONDUIT
WINDOWS AND
#6 x 1-1/4 in. SCREW
TABS THEN TRIM
(4) PROVIDED
SHARP EDGES
BEFORE INSTALLATION
#6 x 1-1/4 in. SCREW
(4) PROVIDED
GASKET CAN BE CUT TO
G01307
GASKET CAN BE CUT TO
INSTALL BEHIND CONDUIT
G01307
SPACER/WALL GASKET
SPACER
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED. INSERT THE
BREAKWAY SEAL (KIT-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
#6 x 2-1/2 in. SCREW
(4) PROVIDED
#6 x 2-1/2 in. SCREW
(4) PROVIDED
1/2 in. and 3/4 in.
CONDUIT WEATHER GASKET
(2) PROVIDED
CONDUIT INSERT
1/2 in. and 3/4 in.
(2) PROVIDED
CONDUIT WEATHER GASKET
INSERT
CONDUIT INSERT
(2) PROVIDED
INSERT
(2) PROVIDED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED. INSERT THE
BREAKWAY SEAL (KIT-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
PERCER DES TROUS DE 3/16 DE DIAMÉTRE 1-1/4
po DE PROFONDEUR POUR UTILISER LES CHEVILLES
PERCER DES TROUS DE 7/64 DE DIAMÉTRE 1-1/4
po DE PROFONDEUR SI LES CHEVILLES
NE SONT PAS UTILISÉES
(4) CHEVILLES MURALES FOURNIES
PLAQUE ARRIÉRE STI-1314 EN OPTION RECOMMANDÉE
POUR LE MONTAGE SUR UNE SURFACE IRRÉGULIÉRE
LANGUETTE DE SÛRETÉ
PERCER UN TROU DE 1/8 po AVEC LE COUVERCLE FERMÉ.
INSÉRER INTÉGRALEMENT LE SCELLÉ DÉTACHABLE
(SUB-65) DANS LA LANGUETTE DE SÛRETÉ
*NE S'UTILISE PAS SUR LES APPLICATIONS DE SIGNAL
D'URGENCE OU D'INCENDIE
INSERT
(2) PROVIDED
CONDUIT INSERT
INSERT
(2) PROVIDED
(2) PROVIDED
1/2 in. and
3/4 in. CONDUIT
WEATHER GASKET
(2) PROVIDED
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
WALL ANCHOR
(4) PROVIDED
BREAK OFF ALL (4) OF THE
CONDUIT WINDOWS AND TABS
THEN TRIM SHARP EDGES
BEFORE INSTALLATION
BREAK OFF ALL (4) OF THE
CONDUIT WINDOWS AND TABS
THEN TRIM SHARP EDGES
BEFORE INSTALLATION
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED. INSERT THE
BREAKWAY SEAL (KIT-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
(2) PROVIDED
STI-1314 OPTIONAL BACKPLATE -
RECOMENDED WHEN
MOUNTING TO UNEVEN SURFACE
G01307 SPACER/WALL GASKET
GASKET CAN BE CUT TO
INSTALL BEHIND CONDUIT
G01307 SPACER/WALL GASKET
GASKET CAN BE CUT TO
INSTALL BEHIND CONDUIT
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED. INSERT THE
CONDUIT INSERT
(2) PROVIDED
1/2 in. and
3/4 in. CONDUIT
WEATHER GASKET
(2) PROVIDED
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
WALL ANCHOR
(4) PROVIDED
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
USING ANCHORS
DRILL 7/64 DIA. HOLES
#8x10 WALL ANCHOR
1-1/4 in. DEEP WHEN
(4) PROVIDED
ANCHORS ARE NOT USED
#8x10 WALL ANCHOR
(4) PROVIDED
STI-1314 OPTIONAL BACKPLATE -
RECOMENDED WHEN
MOUNTING TO UNEVEN SURFACE
Fit appropriate conduit
weather gasket to
conduit. Then fit gasket
to insert or directly to
the housing knock-out.
For additional seal
reliability a bead
of silicone may be
applied to conduit
fitting.
Publicité
