Unit Description; Mixing Fuel; Filling The Fuel Tank - Shindaiwa HT2510/EVC Manuel D'utilisation

Unit Description

Familiarize yourself with your machine and
its various components. Understanding your
machine helps ensure top performance,
long service life, and safer operation.
Prior to use
Before using this product, please make
sure you have all the components required
for a complete unit:
n Engine assembly and gearcase/cutter
assembly
n Combination spark plug/13mm wrench
Carefully inspect all components for damage.
IMPORTANT!
The terms "left," "left-hand," and
"LH"; "right," "right-hand," and "RH" ;
"front" and "rear" refer to directions as
viewed by the operator during normal
operation of this product.
WARNING!
Do not make unauthorized modifica-
tions or alterations to this machine or
any of its components or accessories.

Mixing Fuel

CAUTION!
n Some types of gasoline contain al-
cohol as an oxygenate. Oxygenated
gasoline may cause increased op-
erating temperatures. Under certain
conditions, alcohol-based gasoline
may also reduce the lubricating
qualities of some 2-cycle mixing oils.
n Never use any type of gasoline
containing more than 10% alcohol
by volume! Generic oils and some
outboard oils may not be intended
for use in high-performance 2-cycle
type engines, and should never be
used in your Shindaiwa engine.

Filling the Fuel Tank

WARNING!
Minimize the Risk of Fire!
n ALWAYS stop the engine and allow it
to cool before refueling. Avoid overfill-
ing and wipe off any fuel that may have
spilled.
n Wipe all spilled fuel and move the
engine at least 3 meters from the fueling
point and source before restarting!
HT2510
Fuel Cap
Cover
Fuel Tank
ON-OFF
Switch
Gearcase
DH2510
Cover
Fuel Cap
ON-OFF
Switch
Fuel Tank
Gearcase
Figure 3
CAUTION!
This engine is designed to operate on
a 50:1 mixture consisting of unleaded
gasoline and ISO-L-EGD or JASO FC
class 2-cycle mixing oil only. Use of
non-approved mixing oils can lead to
excessive carbon deposits.
n Use only fresh, clean unleaded gasoline
with a pump octane of 87 or higher.
n Mixed with 50:1 Shindaiwa ISO-L-EGD
or JASO FC class -cycle mixing oil at
a gasoline/ratio of 50:1. Shindaiwa One
meets or exceeds these requirements.
n NEVER start or operate this unit if there
is a fuel leak.
n NEVER start or operate this unit if the
carburetor, fuel lines, fuel tank and/or
fuel tank cap are damaged.
n NEVER smoke or light any fires near the
engine or fuel source!
n NEVER place any flammable material
near the engine muffler!
n NEVER operate the engine without the
muffler and spark arrester in good work-
ing condition.
Guide Bar
Cutter
Protector
Choke
Air Cleaner
Cover
Front Handle
Cutter
Guide Bar
Protector
Choke
Air Cleaner
Cover
Examples of 50:1 mixing quantities
n 1 gallon of gasoline to .6 oz. mixing oil
n 5 liters of gasoline to 100 ml. mixing oil
Mix only enough fuel for your immediate
needs! If fuel must be stored longer than
30 days and
is not used, it should first be treated with
a fuel stabilizer such as STA-BIL™.
fied oil and also meets or exceeds ISO-L-EGD
performance requirements.Shindaiwa One is
recommended for use in all Shindaiwa low emis-
sions engines. Shindaiwa One also includes a
fuel stabilizer.
1. Place the unit on a flat, level surface.
. Clear any dirt or other debris from
around the fuel filler cap.
3. Remove the fuel cap, and fill the tank
with clean, fresh fuel.
4. Reinstall the fuel filler cap and tighten
firmly.
Recoil
Front Handle
Starter
Rear Handle
Muffler
Throttle Trigger
Recoil
Starter
Muffler
Throttle
Trigger
Rear Handle
IMPORTANT!
oil with fuel stabilizer
Oil is a registered JASO FC classi-
5