MALONE
Kayak Carriers
Installation & Loading Instructions - Please Read Before Beginning
Veuillez lire les instructions avant d'entreprendre l'installation et le chargement
Kayak Carriers
Kayak Carriers
1
Installation & Loading Instructions - J-Style Kayak Carriers
12' Load Straps
Installation & Loading Instructions - MPG116MD J-Pro
Installation & Loading Instructions - Please Read Before Beginning
Veuillez lire les instructions avant d'entreprendre l'installation et le chargement
4
1
. Insert Mounting Bolt through one hole of a Jawz
70mm
Adapter and loosely apply a T-knob. See image 2.
60mm
. Faites passer le boulon de fixation dans l'un des trous
70mm
1
d'un adaptateur Jawz puis vissez légèrement un bouton
Mounting Bolts
. Confirm the carriers are in alignment. Firmly tighten
en ''T'' à la base du boulon. (Figure 2)
. Insert Mounting Bolt through one hole of a Jawz adapter.
60mm
the T-knobs until both carriers are securely fixed to
Insert washer and loosely apply a T-knob. See image 2.
Mounting Bolts
the cross bars. See image 5.
3
. Faites passer le boulon de fixation dans l'un des trous
. Assurez-vous que les supports soient bien alignés.
d'un adaptateur Jawz puis vissez légèrement un bouton
. Prior to installation, insert a bolt into the mounting holes in
Insert Mounting Bolt through one hole of a Jawz adapter
Vissez fermement les boutons en ''T'' jusqu'à ce que
en ''T'' à la base du boulon. (Figure 2)
the bottom of the carriers. Push upward to open the two
and loosely apply a T-knob. See image 2.
les deux supports soient solidement fixés aux barres
mounting hole covers located in the Base pads.
transversales. (Figure 5)
. Prior to installation, insert a bolt into the mounting holes in
Insérez Boulon de montage à travers un trou d'un
3
the bottom of the carriers. Push upward to open the two
adaptateur Jawz et appliquer de manière lâche un
. Insert a Mounting Bolt into one mounting hole from the top
6
mounting hole covers located in the Base pads.
Figure 2
T-bouton. (
)
side. Rotate and close the mounting hole cover.
See image 1.
. Insert a Mounting Bolt into one mounting hole from the top
side. Rotate and close the mounting hole cover.
. Insérez un boulon de fixation dans l'un des trous hexagonaux
See image 1.
situés sur le côté supérieur du support.
(Figure 1)
. Insérez un boulon de fixation dans l'un des trous hexagonaux
situés sur le côté supérieur du support.
MALONE
J-Pro2
J-Pro2
MALONE
J-STYLE KAYAK CARRIER
J-STYLE KAYAK CARRIER
J-STYLE KAYAK CARRIER
DownLoader
DownLoader
J-STYLE FOLDING KAYAK CARRIER
12' Load Straps
Jawz Universal Adapters
MALONE
60mm
Load Straps
NOTE: 80mm bolts required for use with Malone trailers.
Load Straps
Jawz Universal Adapters
Jawz Universal Adapters
Instructions - Installation et chargement
R
R
TM
. Insert a Mounting Bolt into one of the top sid
TM
Mounting Bolt Washers
. Insérez un boulon de fixation dans l'un des tr
Mounting Bolt Washers
Base Pad
Covers
T-Knobs
T-Knobs
J-Pro
J-Pro
TM
Jawz Brackets
60mm
Mounting Bolts
70mm
Mounting Bolts
60mm
60mm
Mounting Bolts
. Insert a Mounting Bolt into one of the top side hex holes.
See image 1.
Mounting Bolts
. Insérez un boulon de fixation dans l'un des trous hexagonaux
situés sur le côté supérieur du support.
. Insert a second Mounting Bolt into the top side unused hex
(Figure 1)
. Prior to installation, insert a bolt into the mounting holes in
hole and down through the Jawz mounting adapter. Apply
the bottom of the carriers. Push upward to open the two
a second T-knob and slightly tighten until the carrier is
mounting hole covers located in the Base pads.
secure. Repeat steps 1-4 for the 2nd carrier and rear cross
2
bar. See image 4.
. Insert a Mounting Bolt into one mounting hole from the top
side. Rotate and close the mounting hole cover.
. Insérez un boulon de fixation dans le second trou hexagonal
See image 1.
See image 1.
situé sur le côté supérieur du support et faites-le passer dans
l'adaptateur Jawz. Vissez un bouton en T à la base du second
. Insérez un boulon de fixation dans l'un des trous hexagonaux
boulon, puis serrez légèrement jusqu'à ce que le support soit
situés sur le côté supérieur du support.
bien fixé. Répétez les étapes 1 à 4 pour le deuxième support
(Figure 1)
situés sur le côté supérieur du support.
et la barre transversale arrière. (Figure 4)
2
(Figure 1)
5
12' Safety Lines
12' Safety Lines
2
. Place the carrier onto the front cross bar with the forward
section (with small foam pads) facing out. Swing the Jawz
under the cross bar as shown. See image 3.
. Placez le support sur la barre transversale avant, en vous
assurant que la partie cousinée soit vers l'extérieur. Faites
passer l'adaptateur Jawz sous la barre transversale, tel
. Place the carrier onto the front cross bar with the boarding
qu'indiqué. (Figure 3)
ramp facing out. Swing the Jawz under the cross bar as
. Insert the four Rubber Plugs into the four top side hex holes
shown. See image 3.
in the two carriers. See image 6.
. Placez le support sur la barre transversale avant, la rampe
. Insérez un bouchon de caoutchouc dans chacun des quatre
R
TM
R
TM
Rubber Plugs
70mm
Mounting Bolt Washers
T-Knobs
Rubber Plugs
70mm
70mm
T-Knobs
R
T-Knobs
R
Mounting Bolt
12' Safety Lines
Safety Tie-Downs
12' Safety Lines
T-Knobs
TM
2