Scrolling Help Text In Display Line 3 - red lion IAMS 0001 Mode D'emploi

SCroLLIng HeLp text In DISpLAy LIne 3

[01] Set correct password
[02] Select setup module or NO to store and exit
[03] Select temperature input
Select potentiometer input
Select linear resistance input
Select current input
Select voltage input
[04] Select 0.0­1 V input range
Select 0.2­1 V input range
Select 0­5 V input range
Select 1­5 V input range
Select 0­10 V input range
Select 2­10 V input range
[05] Select 0­20 mA input range
Select 4­20 mA input range
[06] Select 2­wire sensor connection
Select 3­wire sensor connection
Select 4­wire sensor connection
[07] Set resistance value low
[08] Set resistance value high
[09] Select Celsius as temperature unit
Select Fahrenheit as temperature unit
[10] Select TC sensor type
Select Ni sensor type
Select Pt sensor type
[11] Select display unit
[12] Select decimal point position
[13] Set display range low
[14] Set display range high
[15] Set relays in % of input range
Set relays in display units
[16] Select Pt10 as sensor type
Select Pt20 as sensor type
Select Pt50 as sensor type
Select Pt100 as sensor type
Select Pt200 as sensor type
Select Pt250 as sensor type
Select Pt300 as sensor type
Select Pt400 as sensor type
Select Pt500 as sensor type
Select Pt1000 as sensor type
[17] Select Ni50 as sensor type
Select Ni100 as sensor type
Select Ni120 as sensor type
Select Ni1000 as sensor type
[18] Select TC­B as sensor type
Select TC­E as sensor type
Select TC­J as sensor type
Select TC­K as sensor type
Select TC­L as sensor type
Select TC­N as sensor type
Select TC­R as sensor type
Select TC­S as sensor type
Select TC­T as sensor type
Select TC­U as sensor type
Select TC­W3 as sensor type
Select TC­W5 as sensor type
Select TC­Lr as sensor type
[19] Select OFF function ­ relay is permanently off
Select POWER function ­ relay indicates power status OK
Select ERROR function ­ relay indicates sensor error only
Select WINDOW function ­ relay is controlled by 2 setpoints
Select SETPOINT function ­ relay is controlled by 1 setpoint
[20] Select Normally Closed contact
Select Normally Open contact
[21] Set relay setpoint
[22] Activate relay on decreasing signal
Activate relay on increasing signal
[23] Set relay hysteresis
No error action ­ undefined status at error
[24]
Open relay contact at error
Close relay contact at error
Hold relay status at error
Set relay ON delay in seconds
[25]
Set relay OFF delay in seconds
[26]
Relay contact is Open Inside Window
[27]
Relay contact is Closed Inside Window
Set relay window setpoint low
[28]
Set relay window setpoint high
[29]
Set relay window hysteresis
[30]
Open relay contact at error
[34]
Close relay contact at erro
Select current as analogue output type
[36]
Select voltage as analogue output type
Select 0­20 mA output range
[37]
Select 4­20 mA output range
Select S4­20 mA with safety readback
Select 20­0 mA output range
Select 20­4 mA output range
Select S20­4 mA with safety readback
Select no error action ­ output undefined at error
[38]
Select downscale at error
Select NAMUR NE43 downscale at error
Select NAMUR NE43 upscale at error
Select 0.0­1 V output range
[39]
Select 0.2­1 V output range
Select 0­5 V output range
Select 1­5 V output range
Select 0­10 V output range
Select 2­10 V output range
Select 1­0.0 V output range
Select 1­0.2 V output range
Select 5­0 V output range
Select 5­1 V output range
Select 10­0 V output range
Select 10­2 V output range
Set temperature for analogue output low
[41]
Set temperature for analogue output high
[42]
Enter Language setup
[43]
Enter Password setup
Enter simulation mode
Perform process calibration
Enter display setup
Perform memory operations
Load saved setup into device
[44]
Save setup in display front
Adjust LCD contrast
[45]
Adjust LCD backlight
[46]
Write a 6­character device TAG
[47]
Analogue output value is shown in display line 3
[48]
Device TAG is shown in display line 3
Calibrate Input low to process value?
[49]
Calibrate Input high to process value?
[50]
Enable simulation mode?
[51]
Set the input simulation value
[52]
Relay simulation ­ use ^ and v to toggle relay 1
[53]
and 2
Enable password protection?
[54]
Set new password
[55]
[56] Enable Fastset functionality?
Relay setpoint ­ press OK to save
[57]
Relay setpoint ­ Read only
[58]
Select language
[59]
Use process calibration values?
[60]
Set value for low calibration point
[61]
Set value for high calibration poin
[62]
27