TOOLCRAFT 1553060 Mode D'emploi page 4

Operating elements
1 2 3 4 5
6
8 7
Filling
The product is shipped unfilled for safety reasons. When using for the first time, you must first
fill the tank before using the product.
Attention!
Only use commercial lighter gas (isobutane gas) to fill the tank. Suitable refill
cartridges for this purpose are available for purchase (e.g. in 250 ml cans). If in
doubt, consult a specialist.
Never fill the product with other gases/fluids. Never use unsuitable cartridges or
hose connections when filling! There is a great risk of fire or explosion!
Fill the gas tank only in a well ventilated environment and avoid naked flames. There
is a risk of explosion!
Only fill the product after it has cooled down completely.
To fill, proceed as follows:
• First, remove the base (8). Turn the hot-gas burner so the filling valve (7) points vertically
upwards.
• Hold the filling tip of the lighter gas cartridge vertically downwards and stick it into the filling
valve. If necessary, use a suitable adapter (usually supplied with the lighter gas cartridge).
• Then press the filling tip of the lighter gas cartridge against the filling valve. The liquefied gas
now flows into the gas tank. End the filling procedure after 2 to 3 seconds. This filling process
can be repeated 2 or 3 times.
Stop the filling process immediately if any gas escapes. A gas-air mixture could arise
which could explode. Make sure that the room has been well ventilated before you
ignite the product or other sources of ignition.
Wait at least 3 minutes after filling before using the product to allow the gas refill to
stabilise.
Operation
a) Preparation
• Hold the product so the flame nozzle (1) points away from you. Also hold it so that the grip (6)
points downward.
• Slide the gas volume regulator (3) to the right.
• Turn the push button (5) to the right. This unlocks the push button.
b) Igniting the flame
• Press the push button (5) and hold it down firmly. Escaping gas is now ignited by the
integrated piezo ignition. The flame should begin burning.
• If only gas comes out and no flame, let go of the push button and press it again.
c) Flame size and flame type setting
• You can adjust how much gas comes out and how large the flame is by using the gas volume
regulator (3).
• Slide the regulator to the right (+) to increase the gas volume. The flame will be bigger.
• Slide the regulator to the left (–) to reduce the gas volume. The flame will be smaller.
• Use the air volume regulator (2) to adjust how much oxygen is added to the gas before
combustion.
1 Flame nozzle
2 Air volume regulator
3 Gas volume regulator (not depicted)
4 Locking lever
5 Push button
6 Grip with integrated gas tank
7 Filling valve (not depicted)
8 Base
d) Turning off flame, ending operation
• Release the push button (5). The gas valve closes and the flame goes out.
• Turn the push button to the left. This will lock the push button.
• Place the product in the supplied base (8) and let it cool down completely.
• Once the product is completely cooled off, it can be stored in a clean, dry location. Make sure
that the product is always stored upright. Use the provided base for this purpose.
e) Continued use
Use the locking lever (4) to activate continuous operation. Even if the push button (5) is
released, the flame will still burn.
Proceed as follows:
• Press and hold the push button and firmly.
• Slide the locking lever to the left.
• Release the push button. The flame continues to burn.
• To extinguish the flame, slide the locking lever to the right.
Troubleshooting
Flame does not burn or goes out again immediately:
• Slide the gas volume regulator (3) to the right before pressing the push button (5). Only after
a successful ignition should you adjust the desired flame intensity.
• If the regulator is turned too far to the left, too little gas comes out and a flammable mixture
will not form.
• The gas tank is empty and must be refilled.
The push button for the ignition function cannot be pressed:
• Turn the push button (5) to the right. This unlocks the push button.
Gas comes out during filling:
• Use the right adapter during filling. Normally, this is provided with every lighter gas cartridge.
Care and cleaning
• Allow the product to cool down completely before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Disposal
Always dispose of the product according to the relevant statutory regulations.
Technical data
Flame temperature ....................... max. 1300 °C
Fuel ............................................... Butane gas (not included)
Operating time .............................. approx. 60 – 90 minutes
Tank capacity ................................ 22 ml
Operating/storage conditions ........ +20 to +40 °C, 30 – 80 % RH
Dimensions (L x W x H) ................ 102 x 69 x 148 mm
Weight .......................................... 200 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1553060_1_v1_0817_02_IPL_m_en